Nissan 2008 Titan User Manual

Welcome to the growing family of new NISSANowners. This vehicle is delivered to you withconfidence. It was produced using the latesttechniques and str

1. Rear sliding window (if so equipped)(P. 2-52)2. Vehicle loading (P. 9-13)3. Tailgate/Truckbox (P. 3-18)4. Trailer hitch/Towing (if so equipped)(P.

Turn signal/hazard indicatorlightsThe appropriate light flashes when the turn signalswitch is activated.Both lights flash when the hazard switch is tu

The vehicle information displays1is located tothe left of the speedometer. It displays such itemsas:● automatic transmission position indicator● cruis

Fuel Economy mode (If so equipped)The fuel economy mode can be selected to dis-play the instant fuel economy since the last reset.Average speed mode (

Range mode (If so equipped)The range mode can be selected to give you anestimation of the distance that can be drivenbefore refueling. The range is co

Maintenance mode (If so equipped)The maintenance mode allows you to set alertsfor the reminding of maintenance intervals for thefollowing:● engine oil

Vehicle information display warningsand indicators1. Door open warning2. Low fuel warning3. Low windshield washer fluid warning4. Parking brake warnin

Door and liftgate open warningThis warning illuminates when a door, the liftgateor the liftgate glass has been opened when theengine is running.Low fu

Your vehicle may have two types of security sys-tems:● Vehicle security system (if so equipped)● NISSAN Vehicle Immobilizer System (if soequipped)VEHI

moved. If the indicator light fails toglow for 30 seconds, unlock the dooronce and lock it again.● Even when the driver and/or passen-gers are in the

Security indicator lightThe security indicator light blinks whenever theignition switch is in the LOCK, OFF or ACCposition. This function indicates th

1. DVD entertainment system(if so equipped) (P. 4-61)2. Moonroof (if so equipped) (P. 2-53)3. Map lights (if so equipped) (P. 2-56)4. Sun visors (P. 3

CAUTION● Do not operate the washer continu-ously for more than 30 seconds.● Do not operate the washer if the reser-voir tank is empty.● Do not fill th

CAUTIONWhen cleaning the inner side of the rearwindow, be careful not to scratch or dam-age the rear window defroster.HEADLIGHT CONTROL SWITCHLighting

Autolight system (if so equipped)The autolight system allows the headlights to beset so they turn on and off automatically. Theautolight system can:●

Headlight beam selects1To select the high beam function, push thelever forward. The high beam lights come onand thelight illuminates.s2Pull the lever

INSTRUMENT BRIGHTNESSCONTROLThe instrument brightness control operates whenthe headlight control switch is inthe, or AUTO position (with auto-lights a

Push the switch on to warn other drivers whenyou must stop or park under emergency condi-tions. All turn signal lights flash.WARNING● If stopping for

To sound the horn, push the center pad area ofthe steering wheel.WARNINGDo not disassemble the horn. Doing socould affect proper operation of thesuppl

The vehicle should be driven with the VehicleDynamic Control (VDC) system on for most driv-ing conditions.If the vehicle is stuck in mud or snow, the

● Use the E-Lock system only when free-ing a stuck vehicle. Try the 4LO positionbefore using the E-Lock system. Neveruse the E-Lock system on a slippe

Tow mode should be used when pulling a heavytrailer or hauling a heavy load. Using tow mode atother times may cause unnecessary transmissionshifting a

1. Ventilators (P. 4-13)2. Instrument brightness control (P. 2-34)3. Headlight/fog light (if so equipped)/turnsignal switch (P. 2-31)4. Steering wheel

● Use power outlets with the engine run-ning to avoid discharging the vehiclebattery.● Avoid using power outlets when the airconditioner, headlights o

This power outletsAcan be used with an acces-sory cigarette lighter element. Contact yourNISSAN dealer for information.This power outlet can also be u

CONSOLE BOX (if so equipped)Console box storage traysConsole box storagePull up on the levers1to open the console box lids2.Center tray (if so equippe

Console box lockUse the master key to locks1or unlocks2theconsole box.CENTER ARMREST STORAGE (if soequipped)To access the center armrest storage area,

GLOVE BOXOpen the glove box by pulling the handle.Use the master key to lock or unlock the glove boxlock (if so equipped). The valet key cannot beused

MAP POCKETS SEATBACK POCKET (if so equipped)The seatback pocket is located on the back of thedriver’s seat. The pocket can be used to storemaps.OVERHE

Storage binsWARNINGKeep storage bins closed while driving tohelp prevent injury in an accident or asudden stop.Push the button to open a storage bin.P

To open the 2nd row cup holders (rear of frontconsole), lower the lid. To close, raise the lid.Adjustable (if so equipped)LIC0553Armrest (if so equipp

CAUTION● Do not use bottle holder for any otherobjects that could be thrown about inthe vehicle and possibly injure peopleduring sudden braking or an

GROCERY HOOKS (if so equipped)The grocery hooks allow for standard size plasticgrocery bags to hang side by side.To access the grocery hooks, fold up

17. Power outlet/Cigarette lighter(accessory) (P. 2-39/P. 2-41)18. Heated seat switch (if so equipped)(P. 2-36)19. Storage compartment (P. 2-41)20. Ve

POWER WINDOWS (if so equipped)WARNING● Make sure that all passengers havetheir hands, etc. inside the vehicle whileit is in motion and before closing

Rear power window switchThe rear power window switches open or closeonly the corresponding windows. To open thewindow, push the switch and hold it dow

MANUAL WINDOWSThe side windows can be opened or closed byturning the hand crank on each door.REAR SLIDING WINDOW (if soequipped)Squeeze the handles of

NOTE:If the rear power window (if so equipped) islowered while the defroster switch is on,the rear window defroster will automati-cally shut off. The

Auto reverse function (when closing ortilting down the moonroof)The auto reverse function can be activated whenthe moonroof is closed or tilted down b

The interior light has a three-position switch andoperates regardless of ignition switch position.When the switch is in the ON positions1, theinterior

CONSOLE LIGHT (if so equipped)The console lights1will turn on whenever theparking lights or headlights are illuminated.The console light brightness ca

The HomeLinkT Universal Transceiver provides aconvenient way to consolidate the functions of upto three individual hand-held transmitters intoone buil

3. Using both hands, simultaneously press andhold both the HomeLinkT button you want toprogram and the hand-held transmitter but-ton.DO NOT release th

PROGRAMMING HOMELINKT FORCANADIAN CUSTOMERSPrior to 1992, D.O.C. regulations required hand-held transmitters to stop transmitting after 2 sec-onds. To

1. Battery (P. 8-13)2. Fuse/fusible link box (P. 8-20)3. Transmission dipstick (P. 8-11)4. Engine oil filler cap (P. 8-8)5. Brake fluid reservoir (P.

The HomeLinkT Universal Transceiver button hasnow been reprogrammed. The new device canbe activated by pushing the HomeLinkT buttonthat was just progr

3 Pre-driving checks and adjustmentsKeys...3-2NISSAN vehicle immobilizer system keys(if so equipped) ...

1. Two master keys (black) with transpon-der chip (if so equipped) and chromeNISSAN brand symbol on one side2. Valet key (black) with transponder chip

WARNING● Always have the doors locked whiledriving. Along with the use of seat belts,this provides greater safety in the eventof an accident by helpin

LOCKING WITH INSIDE LOCKKNOBTo lock the door without the key, move the insidelock knob to the lock positions1, then close thedoor.To unlock the door w

WIDE OPEN DOORS (if so equipped)CAUTIONDo not open the Wide Open door to thefull open position while the fuel-filler dooris open; only open it as far

3. Open the door to the desired position.CHILD SAFETY REAR DOOR LOCK(Crew Cab models only)Child safety locks help prevent the rear doorsfrom being ope

It is possible to lock/unlock all doors, turn on theinterior lights and puddle lamps (if so equipped),and activate the panic alarm by using the keyfob

● When the button is pushed with alldoors locked, the hazard warning lights flashtwice and the horn beeps once as a re-minder that the doors are alrea

Using the panic alarmIf you are near your vehicle and feel threatened,you may activate the panic alarm to call attentionby pushing and holding thebutt

WarninglightName PageorAnti-lock BrakingSystem (ABS) warn-ing light2-14Automatic transmis-sion check warninglight2-14Automatic transmis-sion park warn

s1Pull the hood lock release handle locatedbelow the driver side instrument panel. Thehood will spring up slightly.s2Push the lever at the front of th

WARNING● Gasoline is extremely flammable andhighly explosive under certain condi-tions. You could be burned or seriouslyinjured if it is misused or mi

TILT OPERATIONWARNINGDo not adjust the steering wheel whiledriving. You could lose control of yourvehicle and cause an accident.Pull the lock lever fo

s1To block glare from the front, swing down themain sun visor.s2To block glare from the side, remove themain sun visor from the center mount andswing

VANITY MIRRORSTo access the vanity mirror, pull the sun visordown and flip open the mirror cover (if soequipped). Some vanity mirrors are illuminateda

AUTOMATIC ANTI-GLAREREARVIEW MIRROR (if so equipped)The inside mirror is designed so that it automati-cally dims according to the intensity of the hea

Manual control type (if so equipped)The outside mirror can be moved in any directionfor a better rear view.Trailer tow mirrors (if so equipped)WARNING

Pull the trailer tow mirror outward to extend it tothe desired position for better visibility while tow-ing a trailer.WARNINGDo not extend or retract

Power folding outside mirrors (if soequipped)CAUTIONDo not manually fold the power foldingmirrors. Manually folding the mirrors candamage the mirrors.

For proper truck box loading see “Vehicle loadinginformation” in the “Technical and consumer in-formation” section of this manual.WARNING● It is extre

IndicatorlightName PageSlip indicator lightfor models withVDC (if soequipped)2-19Turn signal/hazardindicator lights2-20Vehicle dynamiccontrol OFF indi

Locking the tailgateTo unlock the tailgate, turn the key toward thepassenger side of the vehicles1. To lock, turn thekey toward the driver sides2.Both

The automatic drive positioner system has twofeatures:● Memory storage function● Entry/exit functionMEMORY STORAGE FUNCTIONTwo positions for the drive

1. Follow the steps for storing a memory posi-tion.2. While the indicator light for the memoryswitch being set is illuminated for 5 sec-onds, press th

tems” section of this manual. For vehicles withoutnavigation system, see your NISSAN dealer.Restarting the entry/exit functionIf the battery cable is

4 Display screen, heater, air conditioner,audio and phone systemsControl panel buttons (if so equipped) ...4-2How to use the joystick and

Antenna ...4-60NISSAN mobile entertainment system (MES)(if so equipped) ...4-61Digit

WARNING● Positioning of the heating or air condi-tioning controls and display controlsshould not be done while driving in or-der that full attention m

9. GUIDE VOICE button*10.zoom out button*11.zoom in button**For Navigation system control buttons, refer tothe separate Navigation System Owner’sManua

● Average Speed - Average speed driven(MPH or km/h) since the last reset.Resetting trip 1 and trip 2Each trip screen can be reset to 0. Press the TRIP

Maintenance itemsPress the TRIP button to display maintenanceinformation or set maintenance intervals for thefollowing:● Engine Oil● Tire Rotation● Ti

1 Safety—Seats, seat belts andsupplemental restraint systemSeats ...1-2Front manual captain’s chair seat adju

Displaying the maintenance notice re-minderSelect the “Display Maintenance Notification”key and press the ENTER button to display theMAINTENANCE INFOR

Tire pressure rises and falls depending on theheat caused by the vehicle’s operation and theoutside temperature.In case of low tire pressure, a messag

Brightness/contrast:Select the “Brightness/Contrast” key to adjustthe brightness and contrast of the map back-ground. Use the joystick to adjust the b

Vehicle electronic systemsSelect the “Vehicle Electronic Systems” key byusing the joystick and pressing the ENTER but-ton. The VEHICLE ELECTRONIC SYST

● Higher: more sensitive, automatic headlightswill come on quicker when the headlightsensor senses less ambient light.Automatic headlights off delay:

ClockAdjusting the time:Select the “Hours”or “Minutes”key and move thejoystick to the right or left to adjust the time.The time will change step by st

Selecting the time zone:1. Select the “Select Time Zone” key.The TIME ZONE screen will appear.2. Select one of the following zones, depend-ing on the

Adjust air flow direction for the driver and pas-senger sides1, centers2, and rear passenger (ifso equipped)s3ventilators by moving the venti-lator sl

1. Fan speed control dial2. Temperature control dial3. Air flow control dial4. Air conditioner button5. Air recirculation buttonCONTROLSFan control di

● for maximum cooling when using the air con-ditioner.OFF position:Push thebutton again to turn air recircula-tion off. Outside air is drawn into the

WARNING● Do not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt will notbe against your body. In an acc

Bi-level heatingThe bi-level mode directs warmed air to the sideand center vents and to the front and rear flooroutlets.1. Push thebutton to the OFF p

Dehumidified heatingThis mode is used to heat and dehumidify the air.1. Push thebutton to the OFF position.The indicator light on thebutton willgo off

Type AWHA0871Type AWHA08724-18 Display screen, heater, air conditioner, audio and phone systemsZ REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English

Type AWHA0873Type AWHA0874Display screen, heater, air conditioner, audio and phone systems 4-19Z REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English

Type AWHA08754-20 Display screen, heater, air conditioner, audio and phone systemsZ REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English (nna)10/11/0

WARNING● The air conditioner cooling function op-erates only when the engine is running.● Do not leave children or adults whowould normally require th

— Air flows mainly from the frontand rear floor outlets.— Air flows from defroster outletsand the front and rear flooroutlets.Temperature control dial

● To quickly remove ice or fog from the win-dows, turn the fan control dial to 4 and thetemperature control lever to the full HOTposition.● When thepo

5. Turn the temperature control dial to the de-sired position.● For quick cooling when the outside tem-perature is high, push thebutton tothe ON posit

Type BWHA0916Type BWHA0917Display screen, heater, air conditioner, audio and phone systems 4-25Z REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English

Forward and backwardPull the lever up and hold it while you slide theseat forward or backward to the desired position.Release the lever to lock the se

Type BWHA0918Type BWHA09194-26 Display screen, heater, air conditioner, audio and phone systemsZ REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English

Type BWHA0920Display screen, heater, air conditioner, audio and phone systems 4-27Z REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English (nna)10/11/0

WARNING● The air conditioner cooling function op-erates only when the engine is running.● Do not leave children or adults whowould normally require th

— Air flows mainly from the frontand rear floor outlets.— Air flows from defroster outletsand the front and rear flooroutlets.— Air flows mainly from

3. Turn the fan control dial to the desired posi-tion.4. Turn the temperature control dial to the de-sired position.Defrosting or defoggingThis mode d

AIR CONDITIONER OPERATIONStart the engine, turn the fan control dial to thedesired position, and push in thebutton toactivate the air conditioner. Whe

Type CWHA1079Type CWHA10804-32 Display screen, heater, air conditioner, audio and phone systemsZ REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English

Type CWHA1081Type CWHA1082Display screen, heater, air conditioner, audio and phone systems 4-33Z REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English

Type CWHA10834-34 Display screen, heater, air conditioner, audio and phone systemsZ REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English (nna)10/11/0

1. Driver temperature control dial2. A/C ON/OFF button3. Front window defroster button4. Fan speed control dial5. System OFF button6. Rear window defr

MODIFICATION OF YOUR VEHICLEThis vehicle should not be modified.Modification could affect itsperformance, safety or durability, andmay even violate go

Forward and backwardPull the lever up and hold it while you slide theseat forward or backward to the desired position.Release the lever to lock the se

● The temperature of the passenger compart-ment will be maintained automatically. Airflow distribution, fan speed and A/C on/offare also controlled au

The sunload sensors1, located on the top centerof the instrument panel, helps the system main-tain a constant temperature. Do not put anythingon or ar

Reception conditions will constantly change be-cause of vehicle movement. Buildings, terrain,signal distance and interference from other ve-hicles can

AUDIO OPERATION PRECAUTIONSCompact disc (CD) playerCAUTION● Do not force a compact disc into the CDinsert slot. This could damage the CDand/or CD chan

CHECK DISC:● Confirm that the CD is inserted cor-rectly (the label side is facing up,etc.).● Confirm that the CD is not bent orwarped and it is free o

Playback order:Music playback order of a CD with MP3 or WMAfiles is as illustrated.● The names of folders not containing MP3 orWMA files are not shown

Specification chart:Supported media CD, CD-R, CD-RWSupported file systems ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (

Troubleshooting guide:Symptom Cause and CountermeasureCannot playCheck if the disc was inserted correctly.Check if the disc is scratched or dirty.Chec

1. PRESET A·B·C button2.CD eject button3. MENU button4. CD insert slot5. CD button6. FM·AM button7. TUNE buttons8. RPT button9. PWR/VOL control knob10

use the SEEK button to adjust Fader and Balancemodes. Fader adjusts the sound level betweenthe front and rear speakers and Balance adjuststhe sound be

FRONT POWER SEATADJUSTMENT (if so equipped)Operating tips● The power seat motor has an auto-resetoverload protection circuit. If the motorstops during

SEEK buttons:SEEK tuningPress the SEEKor button to seekthrough the frequencies. Seek tuning beginsfrom low to high frequencies, or high to lowfrequenc

RPT button:When the RPT button is pressed while the com-pact disc is being played, the play pattern can bechanged as follows:1 ←→ Normal1: The track t

1. SEEK/TRACK button2. TUNE/FOLDER·CAT button3. DISP button4. SCAN RPT button5. PRESET A·B·C button6. CD·DVD button7. RADIO button*8. AUX button9. REA

1. SEEK/TRACK button2. TUNE/FOLDER·CAT button3. DISP button4. SCAN RPT button5. PRESET A·B·C button6. CD button7. FM button8. AM button9. SAT (satelli

1. SEEK/TRACK button2. CAT FOLDER button3. Display4. SCAN button5. RPT RDM button6. H/M button (clock set buttons)7. PRESET A·B·C button8. CD button9.

1. SEEK/TRACK button2. CAT FOLDER button3. Display4. SCAN RPT button5. DISP button6. H/M button (clock set buttons)7. PRESET A·B·C button8. CD·DVD but

FM/AM/SAT RADIO WITHCOMPACT DISC (CD) CHANGER(Type A, B, C and D) (if so equipped)For all operation precautions, see “Audio opera-tion precautions” ea

● Disc title mode displays the title of the CDbeing played.● Track number mode displays the numberselected disc and the track that is currentlybeing p

pressed unless optional satellite receiver andantenna are installed and an XMT satellite radioservice subscription is active. Satellite radio isnot av

1. Choose preset bank A, B or C using thePRESET A·B·C select button.2. Select the desired FM, AM or SAT stationband.3. Tune to the desired station usi

Seat lifter (if so equipped for driver’sseat)Push the front or rear end of the switch up ordown to adjust the angle and height of the seatcushion.Lumb

SEEK/TRACK button:When thebutton is pressed while a com-pact disc is playing, the track being played re-turns to its beginning. Press several times to

CD EJECT:Current/Selected disc:● Press thebutton, then press the slotnumber (1 – 6) for the desired disc. Thecompact disc will be ejected. If no slot

1. Volume control switch2. MODE select switch3. POWER on/off switch4. Tuning switch1. Volume control switch2. Phone operation switch3. POWER on and MO

Seek tuning (radio):Push the tuning switchor for morethan 1.5 seconds to seek the next or previousradio station.Next/Previous track (CD):Push the tuni

REAR AUDIO CONTROLS (if soequipped)Press the REAR ON·OFF button on the frontradio control panel to turn the rear controls on.Push the button again to

WARNING● The Mobile Entertainment System isdesigned for rear seat passenger view-ing only.● The driver must not attempt to operatethe Mobile Entertain

1. EJECT button2. DVD slot3. ENTER button4. POWER on/off button5. MODE button6. Input jacks7. STOP button8. PLAY/PAUSE button9. MENU button10. DISPLAY

6. DISPLAY button7. MODE button8. SUBTITLE button9. AUDIO button10. ANGLE button11. CLEAR button12. PAUSE button13. PLAY button14. FAST FORWARD/FAST R

HeadphonesPower ON/OFF:Press the power button to turn the headphoneson or off.Volume control:Turn the volume control knob to adjust the vol-ume.The he

Press the REAR ON·OFF button located on thefront controls to disable or enable rear seat audiocontrols. For more information on rear seat audiocontrol

WARNINGHead restraints should be adjusted prop-erly as they may provide significant pro-tection against injury in an accident. Donot remove them. Chec

STOP:Press the STOP button once to stop playing themedia. The display will showin the upperleft corner of the display for 4 seconds, and thelast disc

MENU:If the media is in PLAY mode and the MENUbutton is pressed, the DVD menu will appear onthe screen. Use Navigation Keys to navigatewithin the menu

Do not attempt to operate the system in extremehumidity conditions (less than 10% or more than75%).CAUTION● Do not use any solvents or cleaningsolutio

DVD player operation precautionsDo not use the following DVDs as they maycause the DVD player to malfunction:● 3.1 in (8 cm) discs with an adapter.● D

Remote control and headphonesbattery replacementReplace the battery as follows:1. Open the lid.2. Replace batteries with new ones.● Size AA (remote co

When installing a CB, ham radio or car phone inyour NISSAN, be sure to observe the followingprecautions, otherwise the new equipment mayadversely affe

Your NISSAN is equipped with the BluetoothTHands-Free Phone System. If you have an ap-proved BluetoothT enabled cellular phone, youcan set up the wire

– Your cellular phone is locked to prevent itfrom being dialed.● When the radio wave condition is not idealor ambient sound is too loud, it may bediff

Operating tipsTo get the best performance out of the NISSANVoice Recognition system, observe the following:● Keep the interior of the vehicle as quiet

● Numbers can be spoken in small groups.The system will prompt you to continue en-tering digits, if desired.Example: 1-800-662-6200– “One eight zero z

● Do not attach anything to the head re-straint stalks. Doing so could impairActive Head Restraint function.The Active Head Restraint moves forward ut

PHONE/ENDPress thebutton to cancel a VRsession or end a call.GETTING STARTEDThe following procedures will help you getstarted using the BluetoothT Han

3. Say: “Pair phone”sB. The system acknowl-edges the command and announces thenext set of available commands.4. Say: “New phone”sC. The system acknowl

NOTE:If you do not wish to take the call when youhear the ring tone, press thebuttonon the steering wheel.For additional command options, see “List of

The system acknowledges the command, re-peats the number and begins dialing.If a redial number does not exist, the systemannounces, “There is no numbe

NOTE:Each phone has its own separate phonebook. You cannot access Phone A’s phonebook if you are currently connected withPhone B.“New entry”sAUse the

The transfer procedure varies according to eachcellular phone. See the cellular phone Owner’sManual for details. You can also visitwww.nissanusa.com/b

“Setup”Main Menu“Setup”“Pair Phone”sA“List Phone”sB“Select Phone”sC“Change Priority”sD“Delete Phone”sE“Bluetooth Off”sFUse the Setup command to change

and you change the priority level of Phone C toLevel 1, then:Priority Level 1 = Phone CPriority Level 2 = Phone BPriority Level 3 = Phone A“Delete pho

11. The system will announce that speaker ad-aptation has been completed and the sys-tem is ready.The SA mode will stop if:● Thebutton is pressed for

TROUBLESHOOTING GUIDEThe system should respond correctly to all voicecommands without difficulty. If problems are en-countered, try the following solu

FLEXIBLE SEATINGWARNING● Never allow anyone to ride in the cargoarea or on the rear seats when they arein the fold-down position. In a collision,peopl

5 Starting and drivingPrecautions when starting and driving...5-2Exhaust gas (carbon monoxide) ...5-2Three-way catalyst...

Special winter equipment...5-34Driving on snow or ice ...5-34Engine block heater (if so equipped)...

WARNING● Do not leave children or adults whowould normally require the assistanceof others alone in your vehicle. Petsshould also not be left alone. T

CAUTION● Do not use leaded gasoline. Depositsfrom leaded gasoline will seriously re-duce the three-way catalyst’s ability tohelp reduce exhaust pollut

even if under-inflation has not reached the level totrigger illumination of the TPMS low tire pressuretelltale.Your vehicle has also been equipped wit

● When a spare tire is mounted or a wheelis replaced, tire pressure will not beindicated, the TPMS will not functionand the low tire pressure warning

DRINKING ALCOHOL/DRUGS ANDDRIVINGWARNINGNever drive under the influence of alcoholor drugs. Alcohol in the bloodstream re-duces coordination, delays r

● To avoid raising the center of gravityexcessively, do not exceed the ratedcapacity of the roof rack (if soequipped) and evenly distribute theload. S

● Whenever you drive off-road throughsand, mud or water as deep as thewheel hub, more frequent maintenancemay be required. See “Periodic mainte-nance”

To remove the key from the ignition switch:1. Shift the selector lever to the P (Park) posi-tion with the key in the ON position.2. Turn the key to th

s2Lift up on the latch located on the uppercorner of the seatback to release the back ofthe seat. This will enable you to fold the frontpassenger seat

● Make sure the area around the vehicle isclear.● Check fluid levels such as engine oil, cool-ant, brake fluid, and window washer fluid asfrequently a

ENGINE PROTECTION MODEThe engine has an engine protection mode toreduce the chance of damage if the coolant tem-perature becomes too high (for example

AUTOMATIC TRANSMISSIONWARNING● Do not depress the accelerator pedalwhile shifting from P (Park) or N (Neu-tral) to R (Reverse), or L (Low). Alwaysdepr

WARNINGApply the parking brake if the selectorlever is in any position while the engine isnot running. Failure to do so could causethe vehicle to move

4LO:31 MPH (50 km/h)1 (Low gear):Use this position when climbing steep hills slowlyor slow driving through deep snow, sand or mud,or for maximum engin

brake. When parking on a hill, apply the parkingbrake first, then shift the selector lever into the P(Park) position.R (Reverse):CAUTIONTo prevent tra

M1 (First):Use this position when climbing steep hills slowlyor driving slowly through deep snow, sand ormud, or for maximum engine braking on steepdo

1. Turn the ignition key to the LOCK positionand remove the key2. Apply the parking brake.3. On vehicles equipped with a column shifter,tilt the steer

WARNING● Be sure the parking brake is fully re-leased before driving. Failure to do socan cause brake failure and lead to anaccident.● Do not release

● If the SET indicator light blinks, push thecruise control ON·OFF switch off and havethe system checked by a NISSAN dealer.● The SET indicator light

s2Fold the bottom of the seat cushion towardthe back of the vehicle until it locks in place.s3Repeat this process to raise and secure theseat cushion

To reset at a slower cruising speed, use oneof the following three methods.● Lightly tap the brake pedal. When the ve-hicle attains the desired speed,

● When cruising at highway speeds, it is moreeconomical to use the air conditioner andleave the windows closed to reduce drag.●Use 4H or 4L position o

2WD or 4WD shift procedure:4WD Shift SwitchPositionWheels DrivenIndicator LightUse Conditions 4WD Shift Procedure4WD shift Transfer 4LO position2WDRea

The transfer case 4WD shift switch is used toselect either 2WD or 4WD depending on thedriving conditions. There are three types of drivemodes availabl

When the vehicle is stuck,● Set the 4WD shift switch to 4H or 4LO.● Use the Electronic Locking Rear Differential(E-Lock) system (if so equipped). Turn

The 4WD shift indicator light is located in thevehicle information display.The light should turn off within 1 second afterturning the ignition switch

● When the warning light comes on, the2WD mode may be engaged even if the4WD shift switch is in 4H. Be especiallycareful when driving. If correspondin

CAUTION● After using the E-Lock system, turn theswitch OFF to prevent possible damageto driveline components from extendeduse.● Do not drive the vehic

● HEADED DOWNHILL WITH CURB:sATurn the wheels into the curb and move thevehicle forward until the curb side wheelgently touches the curb.● HEADED UPHI

WARNING● While driving on a slippery surface, becareful when braking, accelerating ordownshifting. Abrupt braking or accel-erating could cause the whe

Folding the rear bench seat downThe rear bench seatback can be tilted forward toaccess the child restraint anchor point locations.To tilt the seatback

WARNINGDo not pump the brake pedal. Doing somay result in increased stoppingdistances.Normal operationThe ABS operates at speeds above3-6MPH(5- 10 km/

When accelerating or driving on slippery sur-faces, the tires may spin or slide. With the VehicleDynamic Control (VDC) system, sensors detectthese mov

● When driving on extremely inclined sur-faces such as higher banked corners,the Vehicle Dynamic Control systemmay not operate properly and the VDCOFF

will sound for only three seconds. Once the sys-tem detects an object approaching, the tone willsound again.The RSS automatically turns on when the sh

3. Tire chains may be used. For details see“Tire chains” in the “Maintenance and do-it-yourself” section of this manual.SPECIAL WINTER EQUIPMENTIt is

To use the engine block heater:1. Turn the engine off.2. Open the hood and unwrap the engine blockheater cord.3. Plug the engine block heater cord int

5-36 Starting and drivingMEMO

6 In case of emergencyFlat tire ...6-2Tire Pressure Monitoring System (TPMS)...6-2Changing a flat tire

TIRE PRESSURE MONITORINGSYSTEM (TPMS)This vehicle is equipped with the Tire PressureMonitoring System (TPMS). It monitors tire pres-sure of all tires

WARNING● Make sure the parking brake is securelyapplied and the automatic transmissionis shifted into P (Park).● Never change tires when the vehicle i

PRECAUTIONS ON SEAT BELTUSAGEIf you are wearing your seat belt properly ad-justed and you are sitting upright and well back inyour seat with both feet

2. Unscrew and remove the jack and tool kit. 3. Assemble the two pieces of the jack rod.Find the oval-shaped opening above themiddle of the license pl

CAUTIONBe sure to center the spare tire suspend-ing plate on the wheel and then lift thespare tire.Jacking up vehicle and removing thedamaged tireWARN

2. Place the jack directly under the jack-uppoint as illustrated so the top of the jackcontacts the vehicle at the jack-up point. Thejack-up points ar

5. Remove the wheel nuts and then remove thetire.Installing the spare tireThe spare tire is designed for emergencyuse. See specific instructions under

Adjust tire pressure to the COLD pressure.COLD pressure: After vehicle has beenparked for three hours or more or drivenless than 1 mile (1.6 km).COLD

● Whenever working on or near a battery,always wear suitable eye protectors (forexample, goggles or industrial safetyspectacles) and remove rings, met

● Make sure the jumper cables do nottouch moving parts in the engine com-partment and that the cable clamps donot contact any other metal.5. Start the

3. Get out of the vehicle. Look and listen forsteam or coolant escaping from the radiatorbefore opening the hood. (If steam or cool-ant is escaping, t

For information about towing your vehicle behinda recreational vehicle (RV), refer to “Flat towing”in the “Technical and consumer information” sec-tio

If the speed or distance must necessarily begreater, remove the propeller shaft before towingto prevent damage to the transmission.Four-wheel drive mo

CALIFORNIA PROPOSITION 65WARNINGWARNINGEngine exhaust, some of its constituents,and certain vehicle components containor emit chemicals known to the S

WARNING● Every person who drives or rides in thisvehicle should use a seat belt at alltimes. Children should be properly re-strained in the rear seat

VEHICLE RECOVERY (freeing a stuckvehicle)Pulling a stuck vehicleIf your vehicle is stuck in sand, snow, mud, etc.,use a tow strap or other device desi

7 Appearance and careCleaning exterior ...7-2Washing ...7-2Waxing...

In order to maintain the appearance of your ve-hicle, it is important to take proper care of it.To protect the paint surfaces, please wash yourvehicle

REMOVING SPOTSRemove tar and oil spots, industrial dust, insects,and tree sap as quickly as possible from thesurface of the paint to avoid lasting dam

Occasionally remove loose dust from the interiortrim, plastic parts and seats using a vacuumcleaner or soft bristled brush. Wipe the vinyl andleather

SEAT BELTSThe seat belts can be cleaned by wiping themwith a sponge dampened in a mild soap solution.Allow the belts to dry completely in the shadebef

● Never allow water or other liquids tocome in contact with electronic compo-nents inside the vehicle as this maydamage them.Chemicals used for road s

8 Maintenance and do-it-yourselfMaintenance requirements...8-2General maintenance ...8-2Explanation

Your new NISSAN has been designed to haveminimum maintenance requirements with longservice intervals to save you both time andmoney. However, some day

When driving in areas using road salt or othercorrosive materials, check lubrication frequently.Lights* Clean the headlights on a regular basis.Make s

WARNING● Always route the shoulder belt overyour shoulder and across your chest.Never put the belt behind your back,under your arm or across your neck

Steering wheel Check for changes in the steer-ing system, such as excessive freeplay, hardsteering or strange noises.Warning lights and chimes Make su

When performing any inspection or maintenancework on your vehicle, always take care to preventserious accidental injury to yourself or damage tothe ve

1. Battery2. Fuse/fusible link box3. Transmission dipstick4. Engine oil filler cap5. Brake fluid reservoir6. Windshield washer fluid reservoir7. Air c

The engine cooling system is filled at the factorywith Genuine NISSAN Long LifeAntifreeze/Coolant to provide year-round anti-freeze and coolant protec

If the cooling system frequently requirescoolant, have it checked by a NISSANdealer.CHANGING ENGINE COOLANTA NISSAN dealer can change the engine coola

5. Remove the dipstick again and check the oillevel. It should be between the H (High) andL (Low) markssB. This is the normal oper-ating oil level ran

If the oil filter is to be changed, remove andreplace it at this time. See “Changing engineoil filter” later in this section.WARNING● Prolonged and re

5. Wipe the engine oil filter sealing surface witha clean rag.CAUTIONBe sure to remove any old gasket materialremaining on the sealing surface of thee

For further brake fluid specification information,refer to “Capacities and recommendedfuel/lubricants” in the “Technical and consumerinformation” sect

Refill the reservoir more frequently when drivingconditions require an increased amount of win-dow washer fluid.Recommended fluid is Genuine NISSAN Wi

There are three basic types of child restraintsystems:● Rear facing child restraint● Front facing child restraint● Booster seatThe proper restraint de

1. Remove the battery caps with a screwdriveras shown. Use a cloth to protect the batterycase.2. Check the fluid level in each cell. If it isnecessary

CAUTION● Do not ground accessories directly tothe battery terminal. Doing so will by-pass the variable voltage control sys-tem and the vehicle battery

1. Visually inspect the belt for signs of unusualwear, cuts, fraying or looseness. If the belt isin poor condition or is loose, have it replacedor adj

The air cleaner filter should not be cleaned andreused. Replace it according to the maintenancelog shown in the “NISSAN Service and Mainte-nance Guide

2. Remove the filter cover bolt and remove thefilter cover.NOTE:The filters are marked with air flow arrows.The end of the filter with the arrow shoul

REPLACINGReplace the wiper blades if they are worn.1. Lift the wiper arm away from the windshield.s2Push the release tab, then move the wiperblade dow

If the brakes do not operate properly, have thebrakes checked by a NISSAN dealer.Self-adjusting brakesYour vehicle is equipped with self-adjustingbrak

If a type A fuse is used to replace a type B fuse,the type A fuse will not be level with the fusepocket as shown in the illustration. This will notaff

5. If the fuse is opensA, replace it with a newfusesB.6. If a new fuse also opens, have the electricalsystem checked and repaired by a NISSANdealer.Fu

5. If the fuse is opensA, replace it with anequivalent good fusesB.6. Push the fuse box cover to install.7. If a new fuse also opens, have the electri

have a label certifying that it complies with Fed-eral Motor Vehicle Safety Standards or CanadianMotor Vehicle Safety Standards. Once the childhas gro

CAUTIONBe careful not to allow children to swallowthe battery and removed parts.Replace the battery in the keyfob as follows:s1Open the lid using a co

This device complies with Part 15 of theFCC Rules and RSS-210 of IndustryCanada.Operation is subject to the following twoconditions: (1) This device m

FOG LIGHTS (if so equipped)Replacing the fog light bulbCAUTION● High pressure halogen gas is sealedinside the halogen bulb. The bulb maybreak if the g

EXTERIOR AND INTERIOR LIGHTSItem Wattage (W) Bulb No.Headlight assemblyHigh 60/65 HB3/9005Low 51/55 HB4/9006Park/Turn 8/27 3457KSidemarker 3.8 194Side

1. Room/map light2. Front personal lights3. Step light4. Puddle lamp/Side turn signal light (if soequipped)5. High-mount stoplight/cargo lights6. Lice

Use a cloths1to protect the housing.Use a cloths1to protect the housing. Use a cloths1to protect the housing.Room/map lightsLDI0389Personal lights (Ty

Use a cloths1to protect the housing. Use a cloths1to protect the housing.Use a cloths1to protect the housing.Step lightLDI0341Puddle lightLDI0388Perso

If you have a flat tire, see the “In case ofemergency” section of this manual.TIRE PRESSURETire Pressure Monitoring System(TPMS)This vehicle is equipp

conditioner and audio systems” section,“Tire Pressure Monitoring System(TPMS)” in the “Starting and driving” sec-tion, and “Flat tire” in the “In case

Tire and loading information labels1Seating capacity: The maximum num-ber of occupants that can be seatedin the vehicle.s2Vehicle load limit: See load

s2Slowly pull the seat belt out of the retractorand insert the tongue into the buckle untilyou hear and feel the latch engage.● The retractor is desig

Checking tire pressure1. Remove the valve stem cap from thetire.2. Press the pressure gauge squarelyonto the valve stem. Do not press toohard or force

TIRE LABELINGFederal law requires tire manufacturers toplace standardized information on thesidewall of all tires. This information iden-tifies and de

s2TIN (Tire Identification Number) for anew tire (example: DOT XX XX XXXXXXX)1. DOT: Abbreviation for the 9Depart-ment Of Transportation.9 The symbolc

s7The word “radial”The word “radial” is shown if the tire hasradial structure.s8Manufacturer or brand nameManufacturer or brand name is shown.Other Ti

If you install snow tires, they must be the samesize, brand, construction and tread pattern on allfour wheels.For additional traction on icy roads, st

Wheel nut tightening torque:98 ft-lb (133 N·m)The wheel nuts must be kept tight-ened to specifications at all times. Itis recommended that wheel nuts

Replacing wheels and tiresWhen replacing a tire, use the same size, treaddesign, speed rating and load carrying capacityas originally equipped. Recomm

If excessive tire wear is found, it is recommendedthat all four tires be replaced with tires of thesame size, brand, construction and tread pattern.Th

9 Technical and consumer informationCapacities and recommended fuel/lubricants ...9-2Fuel recommendation(without Flexible Fuel Vehicle option)..

Readiness for inspection/maintenance (I/M) test ...9-43Event Data Recorders (EDR)...9-44Owner’s Manual/Service Manual order info

WARNINGWhen fastening the seat belts, be certainthat the seatbacks are completely se-cured in the latched position. If they arenot completely secured,

The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the proceduredescribed in the

FUEL RECOMMENDATION (withoutFlexible Fuel Vehicle option)Use unleaded regular gasoline with an octanerating of at least 87 AKI (Anti-Knock Index) num-

Take care not to spill gasoline during refu-eling. Gasoline containing oxygenates cancause paint damage.E–85 fuelE-85 fuel is a mixture of approximate

General informationThis information is for Flexible Fuel vehicles (FFV)only. FFV vehicles can be identified by the fuelfiller door label that states E

CAUTIONDo not use ethanol mixture greater than85% in your vehicle. It will cause difficultyin cold starting and may affect drivability.ENGINE OIL AND

Oil viscosityThe engine oil viscosity or thickness changeswith temperature. Because of this, it is importantto select the engine oil viscosity based o

ENGINEModel VK56DEType Gasoline, 4-cycle, DOHCCylinder arrangement 8-cylinder, V-block, Slanted at 90°Bore x Stroke in (mm) 3.858 x 3.622 (98 x 92)Dis

WHEELS AND TIRESWheels18 x 8.0J20 x 8.0JTiresP265/70R18P275/70R18P275/60R20Spare tire Full sizeDIMENSIONS AND WEIGHTSOverall lengthShort Bed in (mm) 2

When planning to drive your NISSAN ve-hicle in another country, you should first findout if the fuel available is suitable for your vehi-cle’s engine.

ENGINE SERIAL NUMBERThe number is stamped on the engine as shown.F.M.V.S.S./C.M.V.S.S.CERTIFICATION LABELThe Federal/Canadian Motor Vehicle SafetyStan

Shoulder belt height adjustment (frontoutboard seats)The shoulder belt anchor height should be ad-justed to the position best for you. (See “Precau-ti

TIRE AND LOADING INFORMATIONLABELThe cold tire pressure is shown on the Tire andLoading Information label. The label is located asshown.AIR CONDITIONE

WARNING● It is extremely dangerous to ridein a cargo area inside a vehicle. Ina collision, people riding in theseareas are more likely to be seri-ousl

equipped). Do not exceed the number ofoccupants shown as “Seating Capacity”on the Tire and Loading Information label(if so equipped).To get “the combi

Steps for determining correct loadlimit1. Locate the statement “The combinedweight of occupants and cargoshould never exceed XXX kg or XXXlbs” on your

5. Determine the combined weight ofluggage and cargo being loaded onthe vehicle. That weight may notsafely exceed the available cargo andluggage load

1. Side channels2. Header channel3. Channel sections4. Floor channelsUTILI-TRACK™ CHANNEL SYSTEM(if so equipped)WARNING● Properly install and tighten

3. Insert the cleat into the channel perpendicu-lar to the channel as shown. Then rotate thecleat clockwise 90° and slide it to the de-sired location.

5. There should be no gap between the bottomof the cleat and the top of the channel.Tighten the center bolt hand tight (20-40inch pounds).WTI0124Techn

CAUTION● Install only one cleat per section ofchannel.● Applying loads at angles to the cleatsgreater then 45° or loads greater than150 lbs. (header a

WARNINGDo not install accessories over the gapbetween the front and rear side channels.Doing this could affect the rear structurein certain rear impac

Fastening the beltss1Insert the tongue into the buckle until youhear and feel the latch engage.s2Tighten the belt by pulling the free end of thebelt a

Install the channels end stoppers as follows:1. Remove the channel protectors by slidingthem out the back of the truck bed. Properlystore the channel

CREW CAB MODELSCrew Cab short wheel base models shouldnot be used to carry a slide-in camper.KING CAB MODELSThis information is provided for you to pr

When the truck is used to carry a slide-in camper,the total cargo load of the truck consists of thecamper manufacturer’s weight figure, plus:● the wei

WARNINGOverloading or improper loading of atrailer and its cargo can adversely affectvehicle handling, braking and perfor-mance and may lead to accide

Temperature conditions can also affect towing.For example, towing a heavy trailer in high outsidetemperatures on graded roads can affect engineperform

Maximum Gross Vehicle Weight(GVW)/maximum Gross Axle Weight(GAW)The GVW of the towing vehicle must not exceedthe Gross Vehicle Weight Rating (GVWR)sho

Example:● Gross Vehicle Weight (GVW) as weighedon a scale - including passengers, cargo andhitch - 6,200 lb. (2812 kg).● Gross Vehicle Weight Rating (

TOWING LOAD/SPECIFICATIONTowing load specification chart with tow package — short wheel base2WD 4WDKC CC KC CCXE SE LE XE SE LE XE/SE OR LE XE SE LETo

Towing load specification chart with tow package — long wheel base2WD 4WDKC CC KC CCXE SE LE XE SE LE XE SE LE XE/SE OR LETowingCapacity *1, *2, *39,4

Towing load specification chart without tow package — long wheel base2WD 4WDKC CC KC CCXE SE LE XE SE LE XE SE LE XE SE/OR LETowingcapacity*1, *2, *36

s4Loosen the belt by holding the tongue at aright angle to the belt, then pull on the belt.Unfastening the seat beltsTo unfasten the seat belt, press

TOWING SAFETYTrailer hitchYour vehicle may be equipped with an optionaltrailer tow package. The trailer tow package in-cludes a receiver-type frame mo

Bumper towingThe genuine NISSAN step bumper has provi-sions to install a trailer hitch ball and is designedto tow trailers of a maximum weight of 5,00

tem. Follow the instructions provided by themanufacturer for installing and using the swaycontrol device.Class I hitchClass I trailer hitch equipment

● When towing a 5th wheel trailer, do notmake sharp turns while driving or back-ing. The trailer may contact the vehicleand cause damage to both the t

Electric trailer brake controllerTrailers equipped with electric brakes may re-quire the installation of an aftermarket trailerbrake controller.Your v

3. Locate the jumper harness connector underthe lower portion of the instrument panel.The connector is taped to the wiring harnesss1as indicated.● The

Pre-towing tips● Be certain your vehicle maintains a levelposition when a loaded and/or unloadedtrailer is hitched. Do not drive the vehicle if ithas

To drive away:1. Start the vehicle.2. Apply and hold the brake pedal.3. Shift the transmission into gear.4. Release the parking brake.5. Drive slowly

● Do not use cruise control while towing atrailer.● Some states or provinces have specificregulations and speed limits for vehicles thatare towing tra

● DO NOT tow any automatic transmis-sion vehicle with all four wheels on theground (flat towing). Doing so WILLDAMAGE internal transmission partsdue t

● Periodically check to see that the seatbelt and the metal components, such asbuckles, tongues, retractors, flexible wiresand anchors, work properly.

WARNINGThe traction grade assigned to this tire isbased on straight-ahead braking tractiontests, and does not include acceleration,cornering, hydropla

If you believe that your vehicle has a de-fect which could cause a crash or couldcause injury or death, you should immedi-ately inform the National Hi

8. Stop the vehicle. Place the transmission se-lector lever in the P (Park) or N (Neutral)position.9. Turn the engine off.10. Repeat steps1-8atleast o

A genuine NISSAN Service Manual is the bestsource of service and repair information for yourvehicle. Filled with wiring diagrams, illustrationsand ste

Why should you take a chance?In over 40 states, the law says you must beadvised if non-genuine parts are used to repairyour vehicle. And some states h

10 Index4WD warning light ...2-15AActive brake limited slip (ABLS) system(if so equipped) ...5-30Active Head Restraint ...

Cargo (See vehicle loading information) . . .9-13CD care and cleaning ...4-57CD changer (See audio system)...4-55CD player (See audio s

Flat tire ...6-2Floor mat positioning aid...7-4FluidBrake fluid ...8-12Capacities and recommendedfuel/lubr

C.M.V.S.S. certification label...9-11Emission control information label ...9-11Engine serial number ...9-11F.M.V.S.S. certification la

PParkingParking brake operation ...5-18Parking/parking on hills...5-27Pedal position adjustment ...3-12Personal lights ...

NISSAN CARES...Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NIS

● Even with the NISSAN Advanced AirBag System, never install a rear-facingchild restraint in the front seat. An in-flating front air bag could serious

Security system (NISSAN vehicle immobilizersystem), engine start...2-28, 3-2, 5-9Self-adjusting brakes ...8-20Service manual order fo

TransceiverHomeLinkT Universal Transceiver ...2-57TransmissionDriving with automatic transmission . . . .5-12Selector lever lock release ...5-

MEMO

MEMO

MEMO

MEMO

MEMO

RECOMMENDED FUEL (withoutFlexible Fuel Vehicle option):Use unleaded regular gasoline with an octanerating of at least 87 AKI (Anti-Knock Index) num-be

1. Engine coolant 8-72. Battery 8-133. Power steering fluid 8-114. Automatic transmission fluid 8-115. Heater and air conditioner 4-28; Audiosystem 4-

Several manufacturers offer child restraints forinfants and small children of various sizes. Whenselecting any child restraint, keep the followingpoin

● Do not secure a child restraint in thecenter rear seating position using theLATCH anchors. The child restraint willnot be secured properly.● Child r

TOP TETHER STRAP CHILDRESTRAINTIf the manufacturer of your child restraint requiresthe use of a top tether strap, it must be secured tothe anchor poin

Installing top tether strap1. Top tether strap2. Hook3. Anchor pointInstall the top tether strap as follows:1. Raise the head restraint.2. Position th

2. Secure the child restraint anchor attach-ments to the LATCH lower anchors. Checkto make sure the LATCH attachment is prop-erly attached to the lowe

6. Before placing the child in the child restraint,hold the child restraint near the LATCH at-tachment and use force to push the childrestraint from s

3. For child restraints that are equipped withwebbing mounted attachments, remove anyadditional slack from the anchor attach-ments. Press downward and

5. Check to make sure the child restraint isproperly secured prior to each use. If thechild restraint is loose, repeat steps 2through 4.CHILD RESTRAIN

The instructions in this section apply to childrestraint installation using the vehicle seat belts inthe rear seat or the front passenger seat.Front-f

Table ofContentsIllustrated table of contentsSafety—Seats, seat belts and supplemental restraint systemInstruments and controlsPre-driving checks and

3. Route the seat belt tongue through the childrestraint and insert it into the buckle until youhear and feel the latch engage. Be sure tofollow the c

6. Remove any additional slack from the seatbelt; press downward and rearward firmly inthe center of the child restraint with yourknee to compress the

11. If the child restraint is installed in the frontpassenger seat, turn the ignition switch tothe ON position. The front passenger air bagstatus ligh

If you must install a child restraint in the frontcenter bench seat, follow these steps:s1Position the child restraint on the front pas-senger bench s

s3Remove all slack in the lap belt for a very tightfit by pulling forcefully on the lap belt adjust-ment.s4Before placing the child in the child restr

Rear-facingFollow these steps to install a rear-facing childrestraint using the vehicle seat belt in the rearseats:1. Child restraints for infants mus

4. Allow the seat belt to retract. Pull up on theshoulder belt to remove any slack in the belt.5. Remove any additional slack from the childrestraint;

7. Check that the retractor is in the ALR modeby trying to pull more seat belt out of theretractor. If you cannot pull any more seatbelt webbing out o

● Do not use towels, books, pillows orother items in place of a booster seat.Items such as these may move duringnormal driving or a collision and resu

● Make sure the child’s head will be properlysupported by the booster seat or vehicleseat. The seat back must be at or above thecenter of the child’s

Z REVIEW COPY—2008 Titan (tzw)Owners Manual—USA_English (nna)10/11/07—rootX

1. If you must install a booster seat in thefront seat, move the seat to the rear-most position.2. Position the booster seat on the seat. Onlyplace it

4. Position the lap portion of the seat belt lowand snug on the child’s hips. Be sure tofollow the booster seat manufacturer’s in-structions for adjus

PRECAUTIONS ONSUPPLEMENTAL RESTRAINTSYSTEMThis Supplemental Restraint System (SRS) sec-tion contains important information concerningthe following sys

WARNING● The front air bags ordinarily will notinflate in the event of a side impact, rearimpact, rollover, or lower severity fron-tal collision. Alwa

WARNING● Never let children ride unrestrained orextend their hands or face out of thewindow. Do not attempt to hold them inyour lap or arms. Some exam

WARNING● Children may be severely injured orkilled when the front air bags, side airbags or curtain and rollover air bagsinflate if they are not prope

WARNING● Even with the NISSAN Advanced AirBag System, never install a rear-facingchild restraint in the front seat. An in-flating front air bag could

WARNING● The seat belts, the side air bags andcurtain and rollover air bags are mosteffective when you are sitting well backand upright in the seat. T

WARNING● When sitting in the rear seat, do nothold onto the seatback of the front seat.If the side air bag inflates, you may beseriously injured. Be e

1. Roof-mounted curtain side-impact androllover supplemental air bag inflators (ifso equipped)2. Roof-mounted curtain side-impact androllover suppleme

0 Illustrated table of contentsAirbags, seat belts and child restraints ...0-2Exterior front ...0-3Exte

NISSAN Advanced Air Bag System(front seats)This vehicle is equipped with the NISSAN Ad-vanced Air Bag System for the driver and rightfront passenger s

Front passenger air bag status lightWARNINGThe front passenger air bag is designed toautomatically turn OFF under some con-ditions. Read this section

Front passenger seat adult occupants who areproperly seated and using the seat belt as out-lined in this manual should not cause the passen-ger air ba

Other supplemental front-impact air bagprecautionsWARNING● Do not place any objects on the steer-ing wheel pad or on the instrumentpanel. Also, do not

Front seat-mounted side-impactsupplemental air bag and roof-mounted curtain side-impact androllover supplemental air bag systems(if so equipped)The si

WARNING● Do not place any objects near the seat-back of the front seats. Also, do notplace any objects (an umbrella, bag,etc.) between the front door

● If you need to dispose of a pretensioneror scrap the vehicle, contact a NISSANdealer. Correct pretensioner disposalprocedures are set forth in the a

SUPPLEMENTAL AIR BAGWARNING LABELSWarning labels about the supplemental front-impact air bag, front seat-mounted side-impactsupplemental air bag and r

WARNINGIf the supplemental air bag warning lightis on, it could mean that the front air bag,side air bag, curtain and rollover air bagand/or pretensio

Safety—Seats, seat belts and supplemental restraint system 1-63MEMO

1. 2nd row seat belts (P. 1-13)2. Roof-mounted curtain side-impact androll-over supplemental air bag(if so equipped) (P. 1-46)3. Front seat belts (P.

2 Instruments and controlsInstrument panel...2-2Meters and gauges ...2-4Speedometer and o

Storage ...2-41Instrument panel storage trays ...2-41Console box (if so equipped) ...

1. Ventilators (P. 4-13)2. Instrument brightness control (P. 2-34)3. Headlight/fog light (if so equipped)/turnsignal switch (P. 2-31)4. Steering wheel

17. Power outlet/Cigarette lighter(accessory) (P. 2-39/P. 2-41)18. Heated seat switch (if so equipped)(P. 2-36)19. Storage compartment (P. 2-41)20. Ve

1. Warning/indicator lights2. Tachometer3. Engine coolant temperature gauge4. Voltmeter (if so equipped)5. Fuel gauge6. Speedometer7. Automatic transm

1. Speedometer2. Odometer/twin trip display3. Change buttonSPEEDOMETER AND ODOMETERSpeedometerThe speedometer indicates vehicle speed.Odometer/Twin tr

TACHOMETERThe tachometer indicates engine speed in revo-lutions per minute (rpm). Do not rev the engineinto the red zones1.CAUTIONWhen engine speed ap

FUEL GAUGEThe gauge indicates the approximate fuel levelin the tank.The gauge may move slightly during braking,turning, acceleration, or going up or d

CAUTION● This gauge is not designed to indicatelow engine oil level. Use the dipstick tocheck the oil level. (See “Engine oil” inthe “Maintenance and

CAUTION● This gauge is not designed to indicatelow automatic transmission fluid level.Use the dipstick to check the fluid level.(See “5-speed automati

1. Engine hood (P. 3-10)2. Windshield wiper and washer switch(P. 2-29)3. Windshield (P. 8-18)4. Moonroof (if so equipped) (P. 2-53)5. Power windows (P

● When the outside temperature is between140°F (60°C) and 194°F (90°C), the displaywill read 140°F (60°C). When the tempera-ture is above 194°F (90°C)

Zone variation change procedureThe difference between magnetic north and geo-graphical north is known as variance. In someareas, this difference can s

2. Calibrate the compass by driving the vehicleone and a half circles at a maximum speed of6 MPH (10 km/h).3. After completing the circles, the displa

or Anti-lock Braking System (ABS)warning lightLow fuel warning light High beam indicator light (Blue)Automatic transmission check warning light Low ti

or Anti-lock BrakingSystem (ABS)warning lightWhen the ignition switch is in the ON position,the Anti-lock Braking System (ABS) warning lightilluminate

WARNING● Your brake system may not be workingproperly if the warning light is on. Driv-ing could be dangerous. If you judge itto be safe, drive carefu

If the engine or vehicle is not functioning properly,the warning light will either remain illuminated orblink. See “4WD warning light” in the “Startin

WARNING● If the light does not illuminate with theignition switch in the ON position, havethe vehicle checked by a NISSAN dealeras soon as possible.●

If any of the following conditions occur, the frontair bag, side air bag (if so equipped), curtain androll-over air bag (if so equipped), and preten-s

tightly, and that the vehicle has at least 3 gallons(11.4 liters) of fuel in the fuel tank.After a few driving trips, thelight shouldturn off if no ot