®2014 PATHFINDEROWNER’S MANUALFor your safety, read carefully and keep in this vehicle.2014 NISSAN PATHFINDER R52-DR52-DPrinting : May 2013 (04)Pub
1. Front view camera (if so equipped)(P. 4-28)2. Engine hood (P. 8-6)3. Windshield wiper and washer switch,wiper blades (P. 2-28, 8-18)4. Windshield-w
●When a spare tire is mounted or a wheel isreplaced tire pressure will not be indi-cated, the TPMS will not function and thelow tire pressure warning
Refer to “Seat belts” in the “Safety—Seats, seatbelts and supplemental restraint system” sectionfor precautions on seat belt usage.Supplemental air ba
If this indicator light comes on steady for 20 sec-onds and then blinks for 10 seconds when theengine is not running, it indicates that the vehicleis
The light will blink for a few seconds after theVDC system stops limiting wheel spin.Theindicator light also comes on whenyou place the ignition switc
The vehicle information display is located to theleft of the speedometer. It displays such items as:● Vehicle settings● Trip computer information● Dri
SETTINGSThe setting mode allows you to change the infor-mation displayed in the vehicle information dis-play:● Parking Aids (if so equipped)● Vehicle
operation is performed once. From the VehicleSettings menu, select “Selective Unlock”. Usethe ENTER button to activate this function.Auto Door UnlockT
From the “Main Menu Selection” select “FuelEconomy” to display in the vehicle informationdisplay when the ignition is placed in the ONposition.Tire Pr
WARNINGThe tire replacement indicator is not asubstitute for regular tire checks, includ-ing tire pressure checks. See “ChangingWheels and Tires” in “
Use the , , and the ENTER buttons toselect and change the units of the vehicle infor-mation display. The units of the navigation screencan be changed
1. Moonroof (if so equipped)/panoramicsunshade (if so equipped)(P. 2-52, 2-54)2. Antenna (P.4-104)3. Rear window wiper and washer switch(P. 2-29)4. Li
VEHICLE INFORMATION DISPLAYWARNINGS AND INDICATORS1. No Key Detected2. Key ID Incorrect3. Shift to Park4. Push ignition to OFF5. Key battery low6. Eng
12. Timer Alert – Time for a driver break?13. Low Outside Temperature14. Power will turn off to save the battery15. CVT Error: See Owner’s Manual16. R
Low Washer FluidThis warning illuminates when the windshield-washer fluid is at a low level. Add windshield-washer fluid as necessary. See “Windshield
Push to start (if so equipped)This warning appears in the vehicle informationdisplay when the vehicle has been started usingthe remote start function.
4. Confirm that the security indicator lightcomes on. The security light stays on forabout 30 seconds. The vehicle security sys-tem is now pre-armed.
Security indicator lightThe security indicator light blinks whenever theignition switch is placed in the OFF, LOCK or ACCposition. This function indic
SWITCH OPERATIONThe windshield wiper and washer operates whenthe ignition switch is in the ON position.Push the lever down to operate the wiper at the
If the rear window wiper operation is interruptedby snow etc., the wiper may stop moving toprotect its motor. If this occurs, turn the wiperswitch to
NOTE:The top and bottom few rows of wires onthe rear window are not part of the rearwindow defroster system. These wiresmake up the antenna for the au
HEADLIGHT CONTROL SWITCHLighting䊊1When turning the switch to the posi-tion, the front parking, tail, license plate andinstrument panel lights come on.
1. Glove box, Console box (P. 2-47)2. Map lights (P. 2-57)3. Storage (P. 2-43)4. Moonroof (if so equipped)/Panoramicsunshade (if so equipped)(P. 2-52,
NOTE:Autolight activation sensitivity and thetime delay for autolight shutoff can be ad-justed. See “Vehicle information display” inthis section.To tu
DAYTIME RUNNING LIGHT SYSTEM(Canada only)The daytime running lights automatically illumi-nate when the engine is started with the parkingbrake release
FOG LIGHT SWITCH (if so equipped)To turn the fog lights on, turn the headlight switchto theposition, then turn the fog lightswitch to theposition.To t
To sound the horn, push near the horn icon of thesteering wheel.WARNINGDo not disassemble the horn. Doing socould affect proper operation of thesupple
● When cleaning the seat, never usegasoline, benzine, thinner, or any simi-lar materials.● If any malfunctions are found or theheated seat does not op
The rear seats are warmed by built-in heaters.The switches are located on the rear of the frontcenter console and can be operated indepen-dently of ea
NOTE:The heated steering wheel switch isequipped with a 30 minute timer. After theswitch has been activated for 30 minutes,the system will automatical
● Do not put anything on the seat whichinsulates heat, such as a blanket, cush-ion, seat cover, etc. Otherwise, the seatmay become overheated.● Do not
Tow mode should be used when pulling a heavytrailer or hauling a heavy load. Driving the vehiclein the tow mode with no trailer/load or lighttrailer/l
CAUTION● The outlet and plug may be hot duringor immediately after use.● Only certain power outlets are designedfor use with a cigarette lighter unit.
1. Vent (P. 4-39)2. Headlight/fog light (if so equipped)/turnsignal switch (P. 2-31)3. Control panel and Vehicle InformationDisplay switches (P.2-17)4
120V OUTLET (if so equipped)CAUTION● The outlet and plug may be hot duringor immediately after use.● Use power outlets with the engine run-ning to avo
SEATBACK POCKETSThere are two seatback pockets located on theback of the driver and passenger seats. Thepockets can be used to store maps.SUNGLASSES H
CUP HOLDERSCAUTIONDo not recline the rear seatback when youuse the cup holders on the rear armrest.Doing so may cause the beverages to spillover, and
CAUTION● Avoid abrupt starting and braking whenthe cup holder is being used to preventspilling the drink. If the liquid is hot, itcan scald you or you
GLOVE BOXOpen the glove box by pulling the handle. Use themaster key when locking䊊1or unlocking䊊2theglove box.WARNINGKeep glove box lid closed while d
STORAGE TRAYWARNINGDo not place sharp objects in the trays tohelp prevent injury in an accident or sud-den stop.LUGGAGE HOOKSWhen securing items using
CARGO AREA STORAGE BINTo access the floor storage area, push down䊊1to raise the handle, then pull up on the handle tolift the luggage board.ROOF RACK
● Properly secure all cargo with ropes orstraps to help prevent it from sliding orshifting. In a sudden stop or collision,unsecured cargo could cause
Driver’s side power window switchThe driver’s side control panel is equipped withswitches to open or close all of the windows.To open a window, push t
Automatic operationTo fully open a window, press the window switchdown to the second detent and release it; it neednot be held. The window automatical
Heated steering wheel switch(if so equipped) (P.2-38)Power inverter switch (if so equipped)(P.2-40)Power liftgate main switch(if so equipped) (P. 3-26
automatically open or close all the way. To stopthe roof, push the switch once more while it isopening or closing.Tilting the moonroofTo tilt up, firs
SunshadeOpen and close the sunshade by sliding it for-ward or backward.If the moonroof does not closeHave your NISSAN dealer check and repair themoonr
● Do not push the sunshade arm withyour hands, etc., as this may deform it.Improper operation or damage to thesunshade may result.● Do not put any obj
When the ON switch䊊1is pressed, the footwelllights (if so equipped), step lights (if soequipped), map lights and rear personal lightswill automaticall
To turn on the personal lights, press and releasethe switch䊊1.To turn the personal lights off, press and releasethe switch䊊1.Push the button to turn t
CAUTIONDo not use for extended periods of timewith the engine stopped. This could resultin a discharged battery.The HomeLink® Universal Transceiver pr
PROGRAMMING HOMELINK®If you have any questions or are having difficultyprogramming your HomeLink® buttons, refer tothe HomeLink® web site at: www.home
4. At the receiver located on the garage dooropener motor in the garage, locate the“learn” or “smart” button (the name and colorof the button may vary
PROGRAMMING TROUBLE-DIAGNOSISIf the HomeLink® does not quickly learn thehand-held transmitter information:● replace the hand-held transmitter batterie
FCC Notice:For USA:This device complies with Part 15 of theFCC Rules. Operation is subject to the fol-lowing two conditions: (1) This device maynot ca
VQ35DE engine1. Power steering fluid reservoir (P. 8-12)2. Engine coolant reservoir (P. 8-16)3. Drive belt location (P.8-16)4. Fuse box (P. 8-21)5. En
MEMOInstruments and controls 2-63
3 Pre-driving checks and adjustmentsKeys...3-2NISSAN Intelligent Key® ...3-2NISSAN Vehi
Entry/exit function ...3-37Setting memory function...3-38System operation...
1. Intelligent Key (2 sets)2. Mechanical key3. Key number plate (1 plate)NISSAN INTELLIGENT KEY®Your vehicle can only be driven with the IntelligentKe
A key number plate is supplied with your keys.Record the key number and keep it in a safe place(such as your wallet), not in the vehicle. If you losey
CAUTIONAlways carry the mechanical key installedin the Intelligent Key slot.See “Doors” in this section and “Storage” in the“Instruments and controls”
When the doors are locked using one of thefollowing methods, the doors can not be openedusing the inside or outside door handles. Thedoors must be unl
LOCKING WITH INSIDE LOCKKNOBTo lock the door without the key, move the insidelock knob to the lock position䊊1, then close thedoor.To unlock the door w
4. When activated, the hazard indicator willflash twice. When deactivated, the hazardindicator will flash once.5. The ignition switch must be placed i
CAUTION● Be sure to carry the Intelligent Key withyou when operating the vehicle.● Never leave the Intelligent Key in thevehicle when you leave the ve
WarninglightName PageAnti-lock BrakingSystem (ABS) warn-ing light2-10orBrake warning light 2-11Charge warninglight2-11Low tire pressurewarning light2-
If an Intelligent Key is lost or stolen, NISSANrecommends erasing the ID code of that Intelli-gent Key from the vehicle. This may prevent theunauthori
DOOR LOCKS/UNLOCKSPRECAUTION● Do not push the door handle request switchwith the Intelligent Key held in your hand asillustrated. The close distance t
Locking doors1. Move the shift lever to the P (Park) position,place the ignition switch in the LOCK posi-tion and make sure you carry the IntelligentK
Lockout protectionTo prevent the Intelligent Key from being acci-dentally locked in the vehicle, lockout protectionis equipped with the Intelligent Ke
NOTE:Request switches for all doors and liftgatecan be deactivated when the I-Key DoorLock setting is switched to OFF in the Ve-hicle Settings of the
Locking doors1. Place the ignition switch in the LOCK posi-tion.2. Close all doors.3. Press thebutton on the IntelligentKey.4. The hazard warning ligh
NOTE:The unlocking operation can be changed inSelective door unlock in the Vehicle Set-tings of the vehicle information display. Foradditional informa
Using the panic alarmIf you are near your vehicle and feel threatened,you may activate the panic alarm to call attentionby pressing and holding thebut
NOTE:If you change the answer back horn andlight flash feature with the Intelligent Key,the vehicle information display screen willshow the current mo
TROUBLESHOOTING GUIDEVerify the location of all Intelligent Keys that areprogrammed for the vehicle. If another IntelligentKey is in range or inside t
MEMO0-10 Illustrated table of contents
Symptom Possible Cause RemedyWhen pushing the ignition switch to startthe engineThe Intelligent Key battery indicator appearson the display.The batter
The button will be on the NISSAN Intelli-gent Key® if the vehicle has remote engine start.This feature allows the engine to start from out-side the ve
EXTENDING ENGINE RUN TIMEThe remote start feature can be extended onetime by performing the steps listed in “Remotestarting the vehicle” in this secti
䊊1Pull the hood lock release handle locatedbelow the driver side instrument panel. Thehood will spring up slightly.䊊2Push the lever at the front of th
OPERATING THE MANUALLIFTGATE (if so equipped)The power door lock system allows you to lock orunlock all doors including the liftgate simultane-ously.T
OPERATING THE POWER LIFTGATE(if so equipped)WARNING● Make sure that all passengers havetheir hands, etc., inside the vehicle be-fore closing the liftg
Auto Reverse:If an obstacle is detected during power open orpower close, a warning chime will sound and theliftgate will reverse direction and return
POWER LIFTGATE MAIN SWITCHThe power liftgate operation can be turned on oroff by the power liftgate main switch on theinstrument panel.When the power
Power liftgate release (if so equipped)If the liftgate cannot be opened with the instru-ment panel switch, liftgate opener switch or key-fob due to a
To lock, close the fuel-filler door securely andlock the doors.FUEL-FILLER CAPWARNING● Gasoline is extremely flammable andhighly explosive under certa
1 Safety—Seats, seat belts andsupplemental restraint systemSeats . ...1-2Front manual seat adjustment(if so eq
To remove the fuel-filler cap:1. Turn the fuel-filler cap counterclockwise toremove.2. Put the fuel-filler cap on the cap holder䊊1while refueling.To i
MANUAL OPERATION (if soequipped)Tilt and telescopic operationPull the lock lever䊊1down:● Adjust the steering wheel forward or back-ward in direction䊊3
Entry/Exit functionThe automatic drive positioner system will makethe steering wheel move up automatically whenthe driver’s door is opened and the ign
VANITY MIRRORSTo access the vanity mirror, pull the sun visordown and flip open the mirror cover. Some vanitymirrors are illuminated and turn on when
Type A and Type BThe indicator light䊊2will illuminate when theautomatic anti-glare feature is operating.To turn off the automatic anti-glare feature,
OUTSIDE MIRRORSThe outside mirror remote control will operateonly when the ignition switch is in the ACC or ONposition.Move the small switch䊊1to selec
Move the shift lever to R (Reverse). The selectedmirror will turn downward.The selected mirror surface will return to its origi-nal position when any
supplemental restraint system” section, and“Tilt/Telescopic Steering” and “Outside mir-rors” in this section.During this step, do not place the igniti
not be adjusted for the driving position. Note thatthe function is set to disabled as the factorydefault setting.The seat synchronization function ope
The driver’s seat and steering wheel will return tothe previous position:● When the driver’s door is closed with theignition switch placed in the LOCK
WARNING● Do not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt will notbe against your body. In an acc
● When the shift lever is moved from P (Park)to any other position.● When the driver’s door remains open morethan 45 seconds and the ignition switch i
MEMO3-40 Pre-driving checks and adjustments
4 Monitor, climate, audio, phone and voicerecognition systemsControl panel buttons — color screen withoutNavigation System (if so equipped) ...
Manual operation ...4-46Operating tips...4-48Servicing air conditioner...
Manual control ...4-129Troubleshooting guide ...4-130Bluetooth® Hands-Free Phone System withNavigatio
WARNING● Positioning of the heating or air condi-tioning controls and display controlsshould not be done while driving in or-der that full attention m
CAUTION● The glass display screen may break if itis hit with a hard or sharp object. If theglass screen breaks, do not touch it.Doing so could result
HOW TO SELECT MENUS ON THESCREENVehicle functions are viewed on the center dis-play screen in menus. Whenever a menu selec-tion is made or menu item i
Menu Item ResultFuel Economy Displays Fuel Economy menu.Distance to Empty Displays an estimation of the distance that the vehicle can be driven before
HOW TO USE THE SETTINGBUTTONPress the SETTING button. This screen displaysand adjusts various settings and functions thatare available for your vehicl
Welcome to the growing family of new NISSANowners. This vehicle is delivered to you withconfidence. It was produced using the latesttechniques and str
Forward and backwardPull the center of the bar up and hold it while youslide the seat forward or backward to the desiredposition. Release the bar to l
Menu Item ResultAudio See “Audio system” in this section for more information.Display Adjusts the settings for the display screen.Brightness/Contrast
Menu Item ResultComfort & Convenience Select the “Others” key using the NISSAN controller, then select the “Comfort” key. The Comfort settings scr
OFF BUTTONTo change the display brightness, presstheOFF button. Pressing the button againwill change the display to the dayor thenightdisplay. The bri
9. OFF brightness control button10. - (brightness control) button11. VOICE button*12. SETTING button (P. 4-17)13. MAP button*14.BACK (previous) button
To help ensure safe driving, some functions can-not be operated while driving.The on-screen functions that are not availablewhile driving will be “gra
Touch screen maintenanceIf you clean the display screen, use a dry, softcloth. If additional cleaning is necessary, use asmall amount of neutral deter
HOW TO USE THE STATUSBUTTONThe STATUS button is used to display systeminformation. Three different split screens of infor-mation are available. Press
Menu Item ResultFuel Economy Displays Fuel Economy menu.Distance to Empty Displays an estimation of the distance that the vehicle can be driven before
HOW TO USE THE SETTINGBUTTONPress the SETTING button. This screen displaysand adjusts various settings and functions thatare available for your vehicl
Menu Item ResultBackground Color Adjusts the display screen between day and night mode.Color Theme Changes the color of the background, arrows and bar
FRONT POWER SEAT ADJUSTMENT(if so equipped)Operating tips● The power seat motor has an auto-resetoverload protection circuit. If the motorstops during
Menu Item ResultOthers Select the “Others” key using the NISSAN controller. Voice Recognition, language and units setting screen will be displayed.Com
OFF BUTTONTo change the display brightness, presstheOFF button. Pressing the button againwill change the display to the dayor thenightdisplay. The bri
Select the “Full Screen Display” key and pressthe ENTER button to view a full screen version ofthe image.Image requirements:● Image type: JPEG● File e
Slideshow settingsWhile in slideshow mode, the following settingscan be accessed:SettingsSlideshow Speed Changes the frequency at which images are cha
When the shift lever is shifted into the R (Re-verse) position, the monitor display shows a rear-ward view from the vehicle.The system is designed as
Vehicle width guide lines䊊5:Indicate the vehicle width when backing up.Predictive course lines䊊6:Indicate the predictive course when backing up.The pr
3. Slowly back up the vehicle adjusting thesteering wheel so that the predicted courselines䊊Benter the parking space䊊C.4. Maneuver the steering wheel
the hill is the place䊊B. Note that any object onthe hill is further than it appears on the monitor.Backing up on a steep downhillWhen backing up the v
Backing up near a projecting objectThe predicted course lines䊊Ado not touch theobject in the display. However, the vehicle may hitthe object if it pro
OPERATING TIPS● When the shift lever is shifted to the R (Re-verse) position, the display screen automati-cally changes to the RearView Monitormode. H
Seat lifter (driver’s seat)Push the front or rear end of the switch up ordown to adjust the angle and height of the seatcushion.Lumbar support (driver
● The distance between objects viewedon the Around View Monitor differsfrom the actual distance.● The cameras are installed on the frontgrille, the ou
CAUTIONDo not scratch the camera lens whencleaning dirt or snow from the front of thecamera.AVAILABLE VIEWSWARNING● The distance guide line and the ve
Vehicle width guide lines䊊5:Indicate the vehicle width when backing up.Predictive course lines䊊6:Indicate the predictive course when operatingthe vehi
After the ignition switch is placed in the ONposition, the non-viewable area䊊2is highlightedin yellow for three seconds after the bird’s-eyeview is di
CAUTION● The turn signal light may look like theside-of-vehicle line. This is not amalfunction.DIFFERENCE BETWEENPREDICTIVE AND ACTUALDISTANCESBacking
Backing up on a steep downhillWhen backing up the vehicle down a hill, thedistance guide lines and the vehicle width guidelines are shown farther than
There may be a small distance visible betweenthe vehicle and the object in the bird-eye view onthe display䊊B.Backing up behind a projecting objectThe
The display will switch from the Around ViewMonitor screen when:● When the shift lever is in the D (Drive) posi-tion and the vehicle speed increases a
● The system will not detect small objectsbelow the bumper, and may not detectobjects close to the bumper or on theground.● The system may not detect
VIEW MALFUNCTIONWhen the “!” icon is displayed on the screen, theAround View Monitor may not be calibrated cor-rectly. This will not hinder normal dri
2ND ROW BENCH SEATADJUSTMENTForward and backwardPull the center of the bar䊊1up and hold it whileyou slide the seat forward or backward to thedesired p
Adjust air flow direction for the center vents䊊1,driver’s and passenger’s side vents䊊2, and rearvents䊊3by moving the vent slide and/or ventassemblies.
1. Temperature control buttons (driver’sside)2. AUTO climate control ON button3.(front defroster) button4.Air recirculation button5. MODE (manual air
AUTOMATIC OPERATIONCooling and/or dehumidified heating(AUTO)This mode may be used all year round as thesystem automatically works to keep a constantte
Automatic intake air controlIn the AUTO mode, the intake air will be con-trolled automatically. To manually control the in-take air, press theair reci
OPERATING TIPS● When the engine coolant temperature andoutside air temperature are low, the air flowfrom the foot outlets may not operate for amaximum
1.Air recirculation button2. A/C (air conditioner) ON/OFF button3. MODE (manual air flow control) button4. REAR button5. Temperature control buttons (
● Odors from inside and outside the vehiclecan build up in the air conditioner unit. Odorcan enter the passenger compartmentthrough the vents.● When p
MANUAL OPERATIONFan speed controlTurn the fan speed control dial to manuallycontrol the fan speed.Press the AUTO button to return to automaticcontrol
Automatic operation:1. Press the AUTO button. The AUTO indicatorlight will illuminate and “AUTO” will appearon the display.2. Turn the temperature con
1. OFF button2. Fan speed increase (+) button3. AUTO button4.Temperature increase () button5.Temperature decrease () button6. Display7. Fan speed decr
CAUTION● Be careful not to pinch your hand orfoot or bump your head when operatingthe walk-in seat.● Do not drive with the 2nd row seattipped up.● Be
The sunload sensor, located on the top driver’sside of the instrument panel, helps the systemmaintain a constant temperature. Do not put any-thing on
Reception conditions will constantly change be-cause of vehicle movement. Buildings, terrain,signal distance and interference from other ve-hicles can
AUDIO OPERATION PRECAUTIONSCompact disc (CD) player (modelswithout Navigation System)CAUTION● Do not force a compact disc into the CDinsert slot. This
● This audio system can only play pre-recorded CDs. It has no capability torecord or burn CDs.● If the CD cannot be played, one of thefollowing messag
Disc Read Error:● Confirm that the CD/DVD is insertedcorrectly (the label side is facing up,etc.).● Confirm that the CD/DVD is not bentor warped and i
● This copyright protected technologycannot be used without a permit fromMacrovision Corporation. It is limitedto personal use, etc., as long as thepe
● An incorrect song title may appear when thePlay Mode is changed while using an iPod®nano (2nd Generation).● Audiobooks may not play in the same orde
● Sampling frequency — Sampling frequencyis the rate at which the samples of a signalare converted from analog to digital (A/Dconversion) per second.●
Specification chart:Supported media CD, CD-R, CD-RW, USB 2.0Supported file systemsCD, CD-R, CD-RW, ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet* ISO9
Troubleshooting guide:Symptom Cause and CountermeasureCannot playCheck if the CD/USB device was inserted correctly.Check if the CD is scratched or dir
WARNINGWhen returning the seat to its originalposition, confirm that the seat and seat-back are locked properly.Be careful not to pinch your hand or f
CD, DVD or USB with CompressedAudio Files (models with NavigationSystem)The file types supported by this system are MP3,WMA, AAC/M4A and ATRAC3.Explan
Playback order:Music playback order of a CD, DVD or USBdevice with compressed audio files is as illus-trated.● The folder names of folders not contain
Specification chart:Supported media CD, CD-R, CD-RW, DVD-ROM, DVD±R, DVD±RW, DVD±R DL, USB 2.0Supported file systemsCD, CD-R, CD-RW, DVD-ROM, DVD±R, D
Troubleshooting guide:Symptom Cause and CountermeasureCannot playCheck if the CD/DVD/USB device was inserted correctly.Check if the CD/DVD is scratche
Compressed Video Files (models withNavigation System)Explanation of terms:● DivX – DivX refers to the DivX® codecowned by Div, Inc. used for a lossy c
Requirements for Supporting Video Playback:Media CD, CD-R, CD-RW, DVD, DVD±R, DVD±RW, DVD±RW DL, USB 2.0 MemoryFile SystemsCD, CD-R, CD-RW, DVD,DVD±R,
1.CD eject button2. VOL/ON·OFF control knob3. Station and CD select (1 - 6) buttons4. LOAD CD button5. TUNE/FOLDER and AUDIO controlknob (Bass, Treble
Audio settingsAudioBass Adjusts the bass to the desired level.Treble Adjusts the treble to the desired level.Balance Adjusts the balance to the desire
FM/AM radio operationFM/AM band select:Pressing the AM·FM button will change the bandas follows:AM → FM1 → FM2 → AMWhen the AM·FM button is pressed wh
To insert 6 CDs to the CD changer, press theLOAD button for more than 1.5 seconds.The slot numbers (1 – 6) will illuminate on thedisplay when CDs are
1ST ROW HEAD RESTRAINTS/HEADRESTSWARNING● Head restraints/headrests supplementthe other vehicle safety systems. Theymay provide additional protectiona
SCAN button:While listening to a CD, press the SCAN buttonto preview the first 10 seconds of each track onthe CD playing. Pressing the SCAN button aga
1.CD eject button2. VOL/ON·OFF control knob3. Station select (1 - 6) buttons4. TUNE/FOLDER and AUDIO controlknob (Bass, Treble, Fade and Balance)5. AU
Audio settingsAudioBass Adjusts the bass to the desired level.Treble Adjusts the treble to the desired level.Balance Adjusts the balance to the desire
CD/MP3 display modeWhile listening to a CD or an MP3/WMA CD,certain text might be able to be displayed (whenCD encoded with text is being used).Depend
XM band select:Pressing the AUX button will change the band asfollows:USB → XM1* → XM2* → XM3* → AUX → USB(satellite, if so equipped)When the AUX butt
When the “Text” key is selected with the NISSANcontroller on the display while the radio is playing,additional information is displayed on the screen.
CD EJECT button:When thebutton is pressed with the com-pact disc loaded, the compact disc will beejected.When thebutton is pressed while thecompact di
AUX settingsSelect the “Settings”key using the NISSAN con-troller and press the ENTER button.Choose one of the display modes by selectingthe “” key or
1.CD eject button2. VOL/ON·OFF control knob3. Station select (1 - 6) buttons4. TUNE/FOLDER and AUDIO controlknob (Bass, Treble, Fade and Balance)5. DI
Audio settingsAudioBass Adjusts the bass to the desired level.Treble Adjusts the treble to the desired level.Balance Adjusts the balance to the desire
● Adjustable head restraints/headrests havemultiple notches along the stalk to lock themin a desired adjustment position.●The non-adjustable head rest
CD, DVD or USB with compressed audiofilesWhile listening to a CD or compressed audiofiles, certain text might be able to be displayed(when CD encoded
SEEK/CAT and TRACKtuning buttons:For AM or FM:Press the SEEK/CATbutton or theTRACKbutton to tune from high to low orlow to high frequencies and stop a
– Tags the current artist or song playing onSiriusXM Satellite Radio as a favorite.– Turn the Alert ON to indicate whenever afavorite artist or song i
SEEK/CAT and TRACK(Rewind and FastForward) buttons:Press and hold the SEEK/CAT(rewind)button or the TRACK(fast forward) buttonwhile a compact disc is
Normal - Plays all tracks on the CD in sequentialorder until stopped.● Folder ListThe folders on the disc are displayed. Select thekey of a folder nam
AUX (auxiliary) input jacksThe auxiliary input jacks are located inside thecenter console䊊1. NTSC compatible devicessuch as video games, camcorders an
Additional featuresFor more information about the iPod® playeravailable with this system, see “iPod® playeroperation with Navigation System” in this s
Playing a DVDDISC-AUX buttonPark the vehicle in a safe location for the frontseat occupants to operate the DVD drive whilewatching the images.Press th
– Select the directional keys to move thecursor on the DVD menu.– Select the “Enter” key to fix the selectedmenu item.– Select the “Move” key to move
● Display Mode (DVD-VIDEO, VIDEO CD,DVD-VR)Choose from the “Full”, “Wide”, “Normal” or“Cinema” mode.● Title List (DVD-VR)Choose the preferred title fr
Removable (without Dual headrestraint/headrest DVD system only)CAUTIONDo not remove head restraint/headrestfrom vehicles equipped with Dual headrestra
Audio file operationAUX button:Place the ignition switch in the ON or ACCposition and press the AUX button to switch tothe USB input mode. If another
USB INTERFACE (models withNavigation System)Connecting a device to the USB inputjackWARNINGDo not connect/disconnect or operate theUSB device while dr
SEEK/CAT and TRACKbuttons:Press the SEEK/CAT buttonwhile an au-dio file on the USB device is playing to return tothe beginning of the current track. P
Movie file operationPark the vehicle in a safe location for thefront seat occupants to operate the USBmemory while watching the images.DISC-AUX button
Settings:Select the “Settings” key to adjust the followingsettings:● Audio File PlaybackSwitch to the audio playback mode. Thisitem is displayed only
CAUTION● Do not force the USB device into theUSB port. Inserting the USB devicetilted or up-side-down into the port maydamage the port. Make sure that
Interface:The interface for iPod® operation shown on thevehicle center display is similar to the iPod®interface. Use the NISSAN controller and theBACK
CAUTION● Do not force the USB device into theUSB port. Inserting the USB devicetilted or up-side-down into the port maydamage the port. Make sure that
Audio main operationPlace the ignition switch in the ACC or ONposition. Press the DISC·AUX button repeatedlyto switch to the iPod® mode.If the system
● Albums● Songs● Podcasts● Genres● Composers● Audiobooks● Shuffle SongsThe following keys shown on the screen are alsoavailable:● MENU: returns to the
For adjustable head restraint/headrestAdjust the head restraint/headrest so the centeris level with the center of your ears. If your earposition is st
Scrolling menus:While navigating long lists of artists, albums orsongs in the music menu, it is possible to scrollthe list by the first letter. To act
4. A screen will appear asking if you are con-necting the device to use with the hands-free phone system. Select the “No” key.5. Enter a PIN of your c
Bluetooth® audio settingsTo adjust the Bluetooth® audio settings, followthe procedure below:1. Press the SETTING button on the controlpanel.2. Select
6. The Device Name and Device Address aredisplayed on the screen. Select the “Select”key to make this device the activeBluetooth® audio player. Select
1. Menu control switch/ENTER button2.BACK switch3. Volume control switch4. Power on and SOURCE select switchSTEERING WHEEL SWITCH FORAUDIO CONTROLThe
CD:● Tilt up/down for less than 1.5 seconds toincrease or decrease the track number.● Tilt up/down for more than 1.5 seconds toincrease or decrease th
If your vehicle is equipped with the Dual HeadRestraint/Headrest DVD System, you can enjoyplaying video files via a DVD, CD or USB memorythat provides
The angle of the rear display screen can beadjusted for optimal viewing.Gently apply pressure to the base of the screenwhere indicated until the scree
HeadphonesThe headphones for this system are a wirelesstype and no cables are necessary. The head-phones can only be used in the rear seat.Power ON/OF
Channel change:When the rear displays are playing differentsources, slide the channel select switch to selectthe sound.“Left” is the sound on the left
For descriptions specified for four-wheel drivemodels, a 4WD mark is placed at the beginningof the applicable sections/items.As with other vehicles wi
To lower, push and hold the lock knoband push the head restraint/headrestdown.Make sure the head restraint/headrest is posi-tioned so the lock knob is
3. MENU button4. Directional buttons5. Backlight button6. SETUP button7.(next chapter) button8.(fast forward) button9.(stop) button10. Volume control
To replace the battery:1. Open the lid as illustrated.● For headphones, remove the screw䊊1with a flat-bladed screwdriver before re-moving the lid.2. R
CAUTION● Only operate the Dual HeadRestraint/Headrest DVD System whilethe vehicle engine is running. Operatingthe Dual Head Restraint/Headrest DVDSyst
PLAYING A DIGITAL VERSATILEDISC (DVD)DISC·AUX buttonPark the vehicle in a safe location for thefront seat occupants to operate the DVDplayer while wat
SKIP (FORWARD):Select this key and press the ENTER button toskip the chapter(s) of the disc forward. The chap-ters will advance the number of times th
Arrow icons: Move the cursor to select a DVDmenu.Enter: Enter the selected menu.Move: Change the display location by moving theoperation key.Back: Ret
Play Mode:Choose the preferred play mode using theNISSAN controller and press the ENTER button.Remote controller operationUse the remote controller to
Color System:To choose the color system, select from “NTSC”,“PAL”, “PAL-60”, “PAL-M”, “PAL-N” or “AUTO”using the joystick on the remote controller and
CAUTION● Do not use any solvents or cleaningsolutions when cleaning the videosystem.● Do not use excessive force on the moni-tor screen.● Avoid touchi
WARNING● Use a phone after stopping your vehiclein a safe location. If you have to use aphone while driving, exercise extremecaution at all times so f
● Adjustable head restraints/headrests havemultiple notches along the stalk to lock themin a desired adjustment position.● The non-adjustable headrest
phone module when the ignition switch is placedin the ON position with the previously connectedcellular phone turned on and carried in the ve-hicle.Yo
IC Regulatory information– Operation is subject to the following two con-ditions: (1) this device may not cause interfer-ence, and (2) this device mus
● You can cancel a command when the sys-tem is waiting for a response by saying,“Cancel” or “Quit.” The system announces“Cancel” and ends the VR sessi
CONTROL BUTTONSThe control buttons for the Bluetooth® Hands-Free Phone System are located on the steeringwheel.PHONE/SENDPress thebutton to initiate a
1. Press the button on the steeringwheel. The system announces the availablecommands.2. Say: “Connect phone”䊊A. The system ac-knowledges the command a
LIST OF VOICE COMMANDSMain Menu“Call”“Phonebook”“Recent Calls”“Connect Phone”When you press and release the button onthe steering wheel, you can choos
During a callDuring a call there are several command optionsavailable. Press thebutton on the steeringwheel to mute the receiving voice and enter com-
Enter a phone number by voice command:For example, say: “five five five one two one two.”See “How to say numbers” in this section formore information.
“Record Name”䊊BThe system allows you to record custom voicetags for contact names in the phonebook that thevehicle has difficulty recognizing. This fe
VOICE ADAPTATION (VA) MODEVoice Adaptation allows up to two out-of-dialectusers to train the system to improve recognitionaccuracy. By repeating a num
RemovableUse the following procedure to remove the headrestraints/headrests1. Pull the head restraint/headrest up to thehighest position.2. Push and h
● outgoing● call three one nine oh two● nine seven pause pause three oh eight● cancel● call back number● call star two zero nine five● delete phone● d
TROUBLESHOOTING GUIDEThe system should respond correctly to all voicecommands without difficulty. If problems are en-countered, try the following solu
WARNING● Use a phone after stopping your vehiclein a safe location. If you have to use aphone while driving, exercise extremecaution at all times so f
phone module when the ignition switch is placedin the ON position with the connected cellularphone turned on and carried in the vehicle.You can regist
REGULATORY INFORMATIONFCC Regulatory information– CAUTION: To maintain compliance withFCC’s RF exposure guidelines, use only thesupplied antenna. Unau
Menu Item ResultBluetooth ON/OFF Allows user to switch Bluetooth on and off. Bluetooth must be on in order to connect device.On Turns Bluetooth onOff
VEHICLE PHONEBOOKThis vehicle has two phonebooks available foryour use. Depending on your phone, the systemmay automatically download your entire cell
Press the button on the steering wheeland then select the ⬙Vehicle Phonebook⬙ key.Next, select the desired entry from the displayedlist. Select the ⬙E
HANDSET PHONEBOOKMany phones will support an automatic down-load of the cellular phone’s phonebook. Sincethis method allows for up to 1000 numbers to
MAKING A CALLPress the button on the steering wheel.The ⬙Phone⬙ screen will appear on the display.Select one of the following options to make a call:M
For adjustable head restraint/headrestAdjust the head restraint/headrest so the centeris level with the center of your ears. If your earposition is st
RECEIVING A CALLWhen you hear a phone ring, the display willchange to phone mode. To receive a call, followone of the procedures listed below:Menu Ite
DURING A CALLThere are some options available during a call.Select one of the following displayed on thescreen, if necessary:Menu Item ResultHang Up F
PHONE SETTINGSTo set up the Bluetooth Hands-Free Phone Sys-tem to your perferred settings, press the SET-TING button on the control panel and select t
BLUETOOTH SETTINGSTo set up the Bluetooth Hands-Free Phone Sys-tem to your preferred settings, press the SET-TING button on the control panel and sele
CALL VOLUMEAdjusting the incoming or outgoing call volumemay improve clarity if reception between callers isunclear. To access the volume settings, pr
NISSAN Voice Recognition allows hands-freeoperation of the systems equipped on this ve-hicle, such as phone and vehicle information.There are two voic
Menu Item ResultGetting Started The following message will appear: ⬙With voice recognition, you can use voice commands to control navigation, audio, p
Voice recognition settingsThe available settings of the NISSAN Voice Rec-ognition system are described.1. Press the SETTING button on the controlpanel
USING THE SYSTEMInitializationWhen the ignition switch is placed in the ONposition, NISSAN Voice Recognition is initialized,which takes a few seconds.
Operating tips● Say a command after the tone. Voice com-mands cannot be accepted when the iconis.● Commands that are available are alwaysshown on the
To lower, push and hold the lock knoband push the head restraint/headrestdown.Make sure the head restraint/headrest is posi-tioned so the lock knob is
Standard Mode command listCategory Command:COMMAND ACTIONPhone Displays Phone function commands.Navigation Displays Navigation function commands.Infor
Vehicle Information Command:COMMAND ACTIONFuel Economy Displays Fuel Economy information.Maintenance Displays Maintenance information.Traffic Info. Tu
Voice command examplesSome basic voice command examples are de-scribed here.For navigation system commands, see the sepa-rate Navigation System Owner’
● If you say “Change Number” during phonenumber entry, the system will automaticallyrequest that you repeat the number usingthe 3-3-4 format. In this
Please note that in this mode the recognitionsuccess rate may be affected as the number ofavailable commands and ways of speaking eachcommand are incr
Alternate Command Mode command listPhone Command:COMMAND ACTIONDial Number Makes a call to a spoken phone number up to 10 digits.Vehicle Phonebook Mak
COMMAND ACTIONBirdview Map Changes the Map display to Birdview.Planview Map Changes the Map display to a 2-dimensional view.North Up Changes the Map d
Displaying user guideYou can confirm how to use voice commands byaccessing a simplified User Guide, which con-tains basic instructions and tutorials f
Giving voice commands1. Press and release the button locatedon the steering wheel.2. A list of commands appears on the screen,and the system announces
● To minimize the amount of prompts spokenby the system in Alternate Command Mode,use the Minimize Voice Feedback function.To access the Minimize Voic
● Adjustable head restraints/headrests havemultiple notches along the stalk to lock themin a desired adjustment position.● The non-adjustable headrest
SPEAKER ADAPTATION FUNCTIONThe Voice Recognition system has a function tolearn the user’s voice for better voice recognitionperformance. The system ca
TROUBLESHOOTING GUIDEThe system should respond correctly to all voicecommands without difficulty. If problems are en-countered, follow the solutions g
MEMOMonitor, climate, audio, phone and voice recognition systems 4-161
5 Starting and drivingPrecautions when starting and driving...5-2Exhaust gas (carbon monoxide) ...5-2Three-way catalyst...
Special winter equipment...5-33Driving on snow or ice ...5-33Engine block heater (if so equipped) ...
WARNING● Do not leave children or adults whowould normally require the assistanceof others alone in your vehicle. Petsshould also not be left alone. T
WARNING● The exhaust gas and the exhaust sys-tem are very hot. Keep people, animalsor flammable materials away from theexhaust system components.● Do
Additional information:● The TPMS does not monitor the tirepressure of the spare tire.● The TPMS will activate only when the vehicleis driven at speed
● When a spare tire is mounted or a wheelis replaced, tire pressure will not beindicated, the TPMS will not functionand the low tire pressure warning
Operation:1. Add air to the tire.2. After a few seconds, the hazard indicatorswill start flashing.3. When the designated pressure is reached,the horn
RemovableUse the following procedure to remove the headrestraints/headrests1. Pull the head restraint/headrest up to thehighest position.2. Push and h
slide sideways. Be attentive at all times, andavoid driving when tired. Never drive when underthe influence of alcohol or drugs (including pre-scripti
3. When appropriate, slowly release the accel-erator pedal to gradually slow the vehicle.4. Gradually steer the vehicle to a safe locationoff the road
● Do not shift gears while driving ondownhill grades as this could causeloss of control of the vehicle.● Stay alert when driving to the top of ahill.
● Failure to operate this vehicle correctlycould result in loss of control and/or arollover accident.● Always use tires of the same type, size,brand,
The ignition lock is designed so that the ignitionswitch position cannot be switched to OFF untilthe shift lever is moved to the P (Park) position.Whe
ACC (Accessories):This position activates electrical accessories,such as the radio, when the engine is not running.ACC has a battery saver feature tha
3. Touch the ignition switch with the IntelligentKey as illustrated. (A chime will sound.)After step 3 is performed, when the ignitionswitch is pushed
1. Apply the parking brake.2. Move the shift lever to P (Park) or N (Neu-tral). P (Park) is recommended.The starter is designed not to operate ifthe s
CONTINUOUSLY VARIABLETRANSMISSION (CVT)The Continuously Variable Transmission (CVT) inyour vehicle is electronically controlled to pro-duce maximum po
ShiftingPress the button䊊Awhile depressing thebrake pedalPress the button䊊Ato shiftShift without pressing䊊AbuttonAfter starting the engine, fully depr
For adjustable head restraint/headrestAdjust the head restraint/headrest so the centeris level with the center of your ears. If your earposition is st
Shift lock releaseIf the battery charge is low or discharged, theshift lever may not be moved from the P (Park)position even with the brake pedal depr
Fail-safeIf the vehicle is driven under extreme con-ditions, such as excessive wheel spinningand subsequent hard braking, the fail-safesystem may be a
To engage: Firmly depress the parking brake.To release:1. Firmly apply the foot brake.2. Move the shift lever to the P (Park) position.3. Firmly depre
CRUISE CONTROL OPERATIONSThe cruise control allows driving at a speed be-tween 25 - 89 MPH (40 - 144 km/h) withoutkeeping your foot on the accelerator
CAUTIONDuring the first 1,200 miles (2,000 km),follow these recommendations to obtainmaximum engine performance and en-sure the future reliability and
6. Plan for the Shortest Route● Utilize a map or navigation system to de-termine the best route to save time7. Avoid Idling● Shutting off your engine
4X4I SYSTEM OPERATION4WD shift switchThe Four-Wheel Drive (4WD) system is used toselect the 2WD (Two-Wheel Drive), AUTO orLOCK mode depending on the d
4WD mode Wheels driven4WD mode indicatorlightUse conditions2WDFront only – This modeis used when driving ona normal road *12WDFor driving on dry paved
CAUTION● Depending on the driving condition, the4WD mode may automatically changefrom 2WD to 4WD even when the 2WDmode is selected. If this occurs whi
WARNING● Do not stop or park the vehicle overflammable materials such as dry grass,waste paper or rags. They may igniteand cause a fire.● Safe parking
To lower, push and hold the lock knoband push the head restraint/headrestdown.Make sure the head restraint/headrest is posi-tioned so the lock knob is
WARNING● If the engine is not running or is turnedoff while driving, the power assist forthe steering will not work. Steering willbe harder to operate
WARNING● While driving on a slippery surface, becareful when braking, accelerating ordownshifting. Abrupt braking or accel-erating could cause the whe
WARNINGDo not pump the brake pedal. Doing somay result in increased stoppingdistances.Self-test featureThe ABS includes electronic sensors, electricpu
When the VDC system operates, the indi-cator in the instrument panel flashes so note thefollowing:● The road may be slippery or the system maydetermin
● When driving on extremely inclined sur-faces such as higher banked corners,the VDC system may not operate prop-erly and theindicator may flash orbot
● When driving on an unstable surfacesuch as a turntable, ferry, elevator orramp, the VDC warning light may illumi-nate. This is not a malfunction. Re
FREEING A FROZEN DOOR LOCKTo prevent a door lock from freezing, apply de-icer through the key hole. If the lock becomesfrozen, heat the key before ins
● Allow more stopping distance underthese conditions. Braking should bestarted sooner than on dry pavement.● Allow greater following distances onslipp
6 In case of emergencyEmergency engine shut off ...6-2Hazard warning flasher switch ...6-2Flat tire ...
To shut off the engine in an emergency situationwhile driving, perform the following procedure:– Rapidly push the push-button ignition switch 3consecu
● Head restraints/headrests should beadjusted properly as they may providesignificant protection against injury inan accident. Always replace and adju
TIRE PRESSURE MONITORINGSYSTEM (TPMS)This vehicle is equipped with the Tire PressureMonitoring System (TPMS). It monitors tire pres-sure of all tires
4. Turn off the engine.5. Raise the hood to warn other traffic and tosignal professional road assistance person-nel that you need assistance.6. Have a
2. Remove the jack and tool kit cover by liftingup using the handles.3. Remove the tool kit䊊B.● To release the tool kit, release the hookand eye strap
6. Insert the spare tire winch socket䊊Hto thelowering mechanism nut.7. To lower the spare tire, insert the wheel nutwrench䊊Fto the extension䊊Eand inse
2. Place the jack directly under the jack-uppoint as illustrated so the top of the jackcontacts the vehicle at the jack-up point. Thejack-up points ar
NOTE:If the lug nut wrench/jack handle contactsthe ground while raising the vehicle, disas-semble the lug nut wrench from the jackextension rod, rotat
Adjust tire pressure to the COLD pressure.COLD pressure: After vehicle has beenparked for three hours or more or drivenless than 1 mile (1.6 km).COLD
● Whenever working on or near a battery,always wear suitable eye protectors (forexample, goggles or industrial safetyspectacles) and remove rings, met
CAUTION● Always connect positive (⫹) to positive(⫹) and negative (⫺) to body ground (forexample, strut mounting bolt, enginelift bracket, etc.) — not
3. Get out of the vehicle. Look and listen forsteam or coolant escaping from the radiatorbefore opening the hood. (If steam or cool-ant is escaping, t
If you see this symbol, it means “Do not do this”or “Do not let this happen.”If you see a symbol similar to these in an illustra-tion, it means the ar
Folding the 3rd row seatsTo fold the 3rd row seats flat for maximum cargocapacity:1. Pull the strap䊊1to release the headrestraint/headrest forward.2.
For information about towing your vehicle behinda recreational vehicle (RV), refer to “Flat towing”in the “Technical and consumer information” sec-tio
Front-Wheel Drive modelsNISSAN recommends that your vehicle be towedwith the driving wheels (front) off the ground orplace the vehicle on a flat bed t
VEHICLE RECOVERY (freeing a stuckvehicle)Pulling a stuck vehicleWARNINGTo avoid vehicle damage, serious per-sonal injury or death when recovering astu
MEMO6-16 In case of emergency
7 Appearance and careCleaning exterior ...7-2Washing ...7-2Waxing...
In order to maintain the appearance of your ve-hicle, it is important to take proper care of it.To protect the paint surfaces, please wash yourvehicle
REMOVING SPOTSRemove tar and oil spots, industrial dust, insects,and tree sap as quickly as possible from thesurface of the paint to avoid lasting dam
Occasionally remove loose dust from the interiortrim, plastic parts and seats using a vacuumcleaner or soft bristled brush. Wipe the vinyl andleather
FLOOR MATSWARNINGTo avoid potential pedal interference thatmay result in a collision or injury:● NEVER place a floor mat on top of an-other floor mat
Genuine NISSAN floor mats have been speciallydesigned for your vehicle model. The floor matshave grommet holes incorporated in them. Posi-tion each ma
PRECAUTIONS ON SEAT BELTUSAGEIf you are wearing your seat belt properly ad-justed and you are sitting upright and well back inyour seat with both feet
TemperatureHigh temperatures accelerate the rate of corro-sion to those parts which are not well ventilated.Air pollutionIndustrial pollution, the pre
MEMO7-8 Appearance and care
8 Maintenance and do-it-yourselfMaintenance requirements...8-2General maintenance ...8-2Explanation
Your NISSAN has been designed to have mini-mum maintenance requirements with long ser-vice intervals to save you both time and money.However, some day
When driving in areas using road salt or othercorrosive materials, check lubrication frequently.Lights* Clean the headlights on a regular basis.Make s
Seat belts Check that all parts of the seat beltsystem (for example, buckles, anchors, adjustersand retractors) operate properly and smoothly,and are
When performing any inspection or maintenancework on your vehicle, always take care to preventserious accidental injury to yourself or damage tothe ve
VQ35DE engine1. Power steering fluid reservoir2. Engine coolant reservoir3. Drive belt location4. Fuse box5. Engine oil filler cap6. Brake fluid reser
The engine cooling system is filled at the factorywith a pre-diluted mixture of 50% GenuineNISSAN Long Life Antifreeze/Coolant (blue) and50% water to
CHECKING ENGINE COOLANTLEVELCheck the coolant level in the reservoir whenthe engine is cold. If the coolant level is belowthe MIN level, add coolant t
WARNING● Every person who drives or rides in thisvehicle should use a seat belt at alltimes. Children should be properly re-strained in the rear seat
CHECKING ENGINE OIL LEVEL1. Park the vehicle on a level surface and applythe parking brake.2. Start the engine and let it idle until it reachesoperati
CHANGING ENGINE OIL1. Park the vehicle on a level surface and applythe parking brake.2. Start the engine and let it idle until it reachesoperating tem
CHANGING ENGINE OIL FILTER1. Park the vehicle on a level surface and applythe parking brake.2. Turn the engine off.3. Place a large drain pan under th
Check the fluid level in the reservoir.The fluid level should be checked when the fluidis cold at fluid temperatures of 32 to 86ºF (0 to30ºC). The flu
Check the fluid level in the reservoir. If the brakefluid is below the MIN line䊊B, the brake warninglight will illuminate. Add brake fluid up to the M
● Keep the battery surface clean and dry.Clean the battery with a solution of bakingsoda and water.● Make certain the terminal connections areclean an
1. Remove the vent caps with a screwdriver asshown. Use a cloth to protect the batterycase.2. Check the fluid level in each cell. If it isnecessary to
CAUTION● Do not ground accessories directly tothe battery terminal. Doing so will by-pass the variable voltage control sys-tem and the vehicle battery
2. Have the belt checked regularly for condi-tion and tension in accordance with themaintenance schedule found in your“NISSAN Service and Maintenance
Clean and replace the air cleaner filter accordingto the maintenance log shown in the “NISSANService and Maintenance Guide.” When replac-ing the filte
WARNING● Always route the shoulder belt overyour shoulder and across your chest.Never put the belt behind your back,under your arm or across your neck
REPLACINGReplace the wiper blades if they are worn.1. Lift the wiper arm away from the windshield.䊊2Push the release tab, then move the wiperblade dow
Rear window wiper bladeContact a NISSAN dealer if checking or replace-ment is required.If the brakes do not operate properly, have thebrakes checked b
ENGINE COMPARTMENTCAUTIONNever use a fuse of a higher or loweramperage rating than specified on thefuse box cover. This could damage theelectrical sys
PASSENGER COMPARTMENTCAUTIONNever use a fuse of a higher or loweramperage rating than specified on thefuse box cover. This could damage theelectrical
Extended storage switchIf any electrical equipment does not operate,remove the extended storage switch and checkfor an open fuse.NOTE:The extended sto
NISSAN INTELLIGENT KEY®Replace the battery in the Intelligent Key as fol-lows:1. Remove the mechanical key from the Intelli-gent Key.2. Insert a small
NOTE:Changes or modifications not expressly ap-proved by the party responsible for compli-ance could void the user’s authority to op-erate the equipme
EXTERIOR AND INTERIOR LIGHTSItem Wattage (W) Bulb No.Headlight assembly*High 60 HB3Low 55 H11Park 5 W5WTurn 21 WY21WSidemarker 5 WY5WFront fog lights
1. Headlight assembly2 Map light3 Personal light4. Fog light (if so equipped)/ Daytimerunning light (Canada only) (if soequipped)5. Cargo light6. Cour
Use a cloth䊊1to protect the housing.Use a cloth䊊1to protect the housing.Use a cloth䊊1to protect the housing.Personal lightsWDI0670Vanity mirrorLDI2096
PREGNANT WOMENNISSAN recommends that pregnant women useseat belts. The seat belt should be worn snug andalways position the lap belt as low as possibl
If you have a flat tire, see “Flat tire” in the“In case of emergency” section of thismanual.TIRE PRESSURETire Pressure Monitoring System(TPMS)This veh
WARNING● Improperly inflated tires can failsuddenly and cause an accident.● The Gross Vehicle Weight Rating(GVWR) is located on theF.M.V.S.S./C.M.V.S.
Tire and loading information label䊊1Seating capacity: The maximum num-ber of occupants that can be seatedin the vehicle.䊊2Original tire size: The size
Checking tire pressure1. Remove the valve stem cap from thetire.2. Press the pressure gauge squarelyonto the valve stem. Do not press toohard or force
䊊1Tire size (example: P215/65R15 95H)1. P: The “P” indicates the tire is de-signed for passenger vehicles (not alltires have this information).2. Thre
䊊2TIN (Tire Identification Number) for anew tire (example: DOT XX XX XXXXXXX)1. DOT: Abbreviation for the “Depart-ment Of Transportation”. The symbolc
䊊7The word “radial”The word “radial” is shown if the tire hasradial structure.䊊8Manufacturer or brand nameManufacturer or brand name is shown.Other Ti
Generally, snow tires have lower speed ratingsthan factory equipped tires and may not matchthe potential maximum vehicle speed. Never ex-ceed the maxi
Wheel nut tightening torque:83 ft-lb (113 N·m)The wheel nuts must be kept tight-ened to specifications at all times. Itis recommended that wheel nuts
Replacing wheels and tiresWhen replacing a tire, use the same size, treaddesign, speed rating and load carrying capacityas originally equipped. Recomm
䊊2Slowly pull the seat belt out of the retractorand insert the tongue into the buckle untilyou hear and feel the latch engage.● The retractor is desig
If excessive tire wear is found, it is recommendedthat all four tires be replaced with tires of thesame size, brand, construction and tread pattern.Th
MEMO8-40 Maintenance and do-it-yourself
9 Technical and consumer informationCapacities and recommended fuel/lubricants ...9-2Fuel recommendation ...9-3Engine oi
The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the proceduredescribed in the
FUEL RECOMMENDATIONUse unleaded regular gasoline with an octanerating of at least 87 AKI (Anti-Knock Index) num-ber (Research octane number 91).CAUTIO
●If a methanol blend is used, it shouldcontain no more than 5% methanol(methyl alcohol, wood alcohol). It shouldalso contain a suitable amount of appr
ENGINE OIL AND OIL FILTERRECOMMENDATIONSSelecting the correct oilIt is essential to choose the correct grade, qualityand viscosity engine oil to ensur
Your engine was filled with a high-quality engineoil when it was built. You do not have to changethe oil before the first recommended changeinterval.
ENGINEModel VQ35DEType Gasoline, 4-cycle, DOHCCylinder arrangement 6-cylinder, V-block, Slanted at 60°Bore x Stroke in (mm) 3.760 x 3.205 (95.5 x 81.4
WHEELS AND TIRESWheel type Offset in (mm) SizeAluminum 1.97 (50) 18 x 7.5J1.97 (50) 20 x 7.5JSpare Wheel - Steel 18 x4TTire size 235/65R18235/55R20Spa
Unfastening the seat belts䊊1To unfasten the seat belt, press the button onthe buckle. The seat belt automatically re-tracts.Checking seat belt operati
When planning to drive your NISSAN ve-hicle in another country, you should first findout if the fuel available is suitable for your vehi-cle’s engine.
ENGINE SERIAL NUMBERThe number is stamped on the engine as shown.F.M.V.S.S./C.M.V.S.S.CERTIFICATION LABELThe Federal/Canadian Motor Vehicle SafetyStan
TIRE AND LOADING INFORMATIONLABELThe cold tire pressure is shown on the Tire andLoading Information label. The label is located asshown.AIR CONDITIONE
WARNING● It is extremely dangerous to ridein a cargo area inside a vehicle. Ina collision, people riding in theseareas are more likely to be seri-ousl
VEHICLE LOAD CAPACITYDo not exceed the load limit of your ve-hicle shown as “The combined weight ofoccupants and cargo” on the Tire andLoading Informa
Steps for determining correct loadlimit1. Locate the statement “The combinedweight of occupants and cargoshould never exceed XXX lbs or XXXkg” on your
5. Determine the combined weight ofluggage and cargo being loaded onthe vehicle. That weight may notsafely exceed the available cargo andluggage load
LOADING TIPS● The GVW must not exceed GVWRor GAWR as specified on theF.M.V.S.S./C.M.V.S.S. certificationlabel.● Do not load the front and rear axle to
MAXIMUM LOAD LIMITSMaximum trailer loadsNever allow the total trailer load to exceed thevalue specified in the following TowingLoad/Specification Char
Tongue loadWhen using a weight carrying or a weight distrib-uting hitch, keep the tongue load between 10 -15 percent of the total trailer load or use
WARNING● After adjustment, release the adjust-ment button and try to move the shoul-der belt anchor up and down to makesure it is securely fixed in po
To determine the available towing capacity, usethe following procedure.1. Find the GCWR for your vehicle on the⬙Towing Load/Specification⬙ chart found
TOWING LOAD/SPECIFICATIONTOWING LOAD/SPECIFICATION CHARTU.S. and CanadaMaximum Towing Capacity*1 5,000lb.(2,268 kg)Maximum Tongue Load 500 lb.(227 kg)
WARNINGTrailer hitch components have specificweight ratings. Your vehicle may be ca-pable of towing a trailer heavier than theweight rating of the hit
WARNINGProperly adjust the weight distributinghitch so the rear of the bumper is nohigher than the measured referenceheight when the trailer is attach
Trailer lights should comply with federal and/orlocal regulations. For assistance in hooking uptrailer lights, contact a NISSAN dealer or repu-table t
2. Locate the jumper harness connector underthe lower portion of the instrument panel.The connector is taped to the wiring harness䊊1as indicated.● The
● Keep the cargo load as low as possible inthe trailer to keep the trailer center of gravitylow.● Load the trailer so approximately 60% of thetrailer
● While going downhill, the weight of thetrailer pushing on the tow vehicle may de-crease overall stability. Therefore, to main-tain adequate control,
● When launching a boat, don’t allow the wa-ter level to go over the exhaust tail pipe orrear bumper.● Make sure you disconnect the trailer lightsbefo
DOT (Department of Transportation) QualityGrades: All passenger car tires must conform tofederal safety requirements in addition to thesegrades.Qualit
SEAT BELT MAINTENANCE● To clean the seat belt webbing, apply amild soap solution or any solution recom-mended for cleaning upholstery or carpet.Then w
Your NISSAN vehicle is covered by the followingemission warranties:For USA1. Emission Defects Warranty2. Emissions Performance WarrantyDetails of this
Additional information concerning motorvehicle safety may be obtained from Trans-port Canada’s Road Safety InformationCentre at 1-800-333-0371 or onli
This vehicle is equipped with an Event Data Re-corder (EDR). The main purpose of an EDR is torecord, in certain crash or near crash-like situa-tions,
MEMO9-32 Technical and consumer information
10 IndexAAir bag (See supplemental restraintsystem)...1-53Air bag systemFront (See supplemental front impactair bag system) ...
Cleaning exterior and interior ...7-2C.M.V.S.S. certification label ...9-10Cold weather driving ...5-33Compact disc (CD) pla
Fueloctanerating...9-4Fuel recommendation ...9-3Loosefuelcapwarning...2-26,3-28Fuses...8-21Fusiblelinks
LightAirbagwarninglight...1-68,2-14Brakelight(Seestoplight)...8-26Bulb check/instrument panel ...2-10Bulb replacement ...8
Power steering system ...5-27Power windows ...2-50Rear power windows ...2-51Powerinverterswitch...2-40Precauti
Precautions on supplemental restraintsystem...1-53Supplemental restraint system(Supplemental air bag system) ...1-53SwitchAutol
All U.S. states and Canadian provinces or terri-tories require the use of approved child restraintsfor infants and small children. See “Child re-strai
Low windshield-washer fluid warninglight...2-25Passenger air bag and status light ...1-62Seat belt warning light...2-13V
RECOMMENDED FUEL:Use unleaded regular gasoline with an octanerating of at least 87 AKI (Anti-Knock Index) num-ber (Research octane number 91).CAUTION●
®2014 PATHFINDEROWNER’S MANUALFor your safety, read carefully and keep in this vehicle.2014 NISSAN PATHFINDER R52-DR52-DPrinting : May 2013 (04)Pub
NISSAN CARES...Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NIS
PRECAUTIONS ON CHILDRESTRAINTSWARNING● Failure to follow the warnings and in-structions for proper use and installa-tion of child restraints could res
– Child restraint anchor points are de-signed to withstand loads from childrestraints that are properly fitted.– Never use the anchor points for adult
LATCH (Lower Anchors and Tethersfor CHildren) SYSTEMYour vehicle is equipped with special anchorpoints that are used with LATCH (Lower Anchorsand Teth
LATCH lower anchor locationThe LATCH lower anchors are located at the rearof the seat cushion near the seatback. A label isattached to the seatback to
When installing a child restraint, carefully readand follow the instructions in this manual andthose supplied with the child restraint.Top tether anch
Top tether anchor point locationsAnchor points are located in the following loca-tions:● 2nd row bench on the bottom of the seat-back in the seating p
3. For child restraints that are equipped withwebbing-mounted attachments, remove anyadditional slack from the anchor attach-ments. Press downward and
5. Check to make sure the child restraint isproperly secured prior to each use. If thechild restraint is loose, repeat steps 2through 4.REAR-FACING CH
Refer to all Warnings and Cautions in the “Childsafety” and “Child restraints” sections before in-stalling a child restraint.Follow these steps to ins
4. Allow the seat belt to retract. Pull up on theshoulder belt to remove any slack in the belt.5. Remove any additional slack from the seatbelt; press
Table ofContentsIllustrated table of contentsSafety—Seats, seat belts and supplemental restraint systemInstruments and controlsPre-driving checks and
7. Check to make sure that the child restraint isproperly secured prior to each use. If theseat belt is not locked, repeat steps 1through 6.After the
If the seating position does not have anadjustable head restraint/headrest and it isinterfering with the proper child restraint fit,try another seatin
7. Check to make sure the child restraint isproperly secured prior to each use. If thechild restraint is loose, repeat steps 3through 6.FORWARD-FACING
3. Route the seat belt tongue through the childrestraint and insert it into the buckle until youhear and feel the latch engage. Be sure tofollow the c
6. Remove any additional slack from the seatbelt; press downward and rearward firmly inthe center of the child restraint with yourknee to compress the
10. If the child restraint is installed in the frontpassenger seat, place the ignition switch inthe ON position. The front passenger air bagstatus lig
If you have any questions when installing atop tether strap, consult your NISSANdealer for details.1. Top tether strap2. Anchor pointINSTALLING TOP TE
BOOSTER SEATSPrecautions on booster seatsWARNINGIf a booster seat and seat belt are not usedproperly, the risk of a child being injuredin a sudden sto
Booster seats of various sizes are offered byseveral manufacturers. When selecting anybooster seat, keep the following points in mind:● Choose only a
1. If you must install a booster seat in thefront seat, move the seat to the rear-most position.2. Position the booster seat on the seat. Onlyplace it
7. If the booster seat is installed in the frontpassenger seat, place the ignition switch inthe ON position. The front passenger air bagstatus lightma
WARNING● The front air bags ordinarily will notinflate in the event of a side impact, rearimpact, rollover, or lower severity fron-tal collision. Alwa
WARNING● Never let children ride unrestrained orextend their hands or face out of thewindow. Do not attempt to hold them inyour lap or arms. Some exam
ARS1042 ARS1043 ARS10441-56 Safety—Seats, seat belts and supplemental restraint system
WARNING● Children may be severely injured orkilled when the front air bags, side airbags or curtain air bags inflate if theyare not properly restraine
WARNING● The seat belts, the side air bags andcurtain air bags are most effective whenyou are sitting well back and upright inthe seat with both feet
WARNING● When sitting in the 2nd row rear seat, donot hold onto the seatback of the frontseat. If the side air bag inflates, you maybe seriously injur
1. Supplemental front-impact air bagmodules2. Air bag Control Unit (ACU)3. Occupant classification sensor(weight sensor)4. Front seat-mounted side-imp
● Do not place heavy loads heavier than2.2 lb (1 kg) on the seatback, headrestraint/headrest or in the seatbackpocket.● Do not store luggage behind th
When a front air bag inflates, a fairly loud noisemay be heard, followed by the release of smoke.This smoke is not harmful and does not indicate afire
0 Illustrated table of contentsAir bags, seat belts and child restraints ...0-2Exterior front ...0-3Exte
Status lightThe front passenger air bag status lightislocated near the radio controls. After the ignitionswitch is placed in the ⬙ON⬙ position, the fr
Using the passenger air bag status light, you canmonitor when the front passenger air bag is au-tomatically turned OFF with the seat occupied.The ligh
● Modifying or tampering with the frontpassenger seat may result in seriouspersonal injury. For example, do notchange the front seats by placing mate-
They are designed to inflate on the side where thevehicle is impacted. They may not inflate in cer-tain side collisions.Curtain air bags are also desi
● Tampering with the side air bag systemmay result in serious personal injury.For example, do not change the frontseats by placing material near the s
When selling your vehicle, we request that youinform the buyer about the pretensioner systemand guide the buyer to the appropriate sectionsin this Own
If any of the following conditions occur, the frontair bag, side air bag, curtain air bag and preten-sioner systems need servicing:● The supplemental
2 Instruments and controlsInstrument panel...2-2Meters and gauges ...2-3Speedometer and o
Seatback pockets ...2-44Sunglasses holder ...2-44Cup holders ...2-4
1. Vent (P. 4-39)2. Headlight/fog light (if so equipped)/turnsignal switch (P. 2-31)3. Control panel and Vehicle InformationDisplay switches (P.2-17)4
1. Supplemental front-impact air bags(P.1-53)2. Occupant classification sensor(weight sensor)3. Seat belts (P. 1-24)4. Head restraints/headrests (P.1-
Heated steering wheel switch (if soequipped) (P.2-38)Power inverter switch (if so equipped)(P.2-40)Power liftgate main switch (if soequipped) (P. 3-26
SPEEDOMETER AND ODOMETERSpeedometerThe speedometer indicates vehicle speed.Odometer/Twin trip odometerThe odometer䊊1and the twin trip odometer䊊2are di
ENGINE COOLANT TEMPERATUREGAUGEThe gauge indicates the engine coolant tempera-ture. The engine coolant temperature is within thenormal range䊊1when the
The indicates that the fuel-filler door islocated on the driver’s side of the vehicle.CAUTION● If the vehicle runs out of fuel, theMalfunction Indicat
COMPASS DISPLAYPush the or button for about 1 sec-ond when the ignition switch is placed in the ONposition to toggle the compass direction display䊊1on
Zone variation change procedureThe difference between magnetic north and geo-graphical north is known as variance. In someareas, this difference can s
Inaccurate compass direction:The compass display is equipped with automaticcorrection function. If the correct direction is notshown, follow this proc
Anti-lock Braking System (ABS) warning light Supplemental air bag warning light Slip indicator lightor Brake warning lightFront fog light indicator li
If the ABS light comes on while the engine isrunning, it may indicate the anti-lock braking sys-tem is not functioning properly. Have the systemchecke
The low tire pressure warning light warns of lowtire pressure or indicates that the TPMS is notfunctioning properly.After the ignition switch is place
Comments to this Manuals