2009 NISSAN ALTIMA 2009 ALTIMAOWNER'S MANUALL32-DPrinting : March 2009 (10)Publication No.: OM9E-0L32U2Printed in U.S.A.For your safety, rea
Sedan1. Power windows (P. 2-44)2. Windshield (P. 8-20)3. Windshield wiper and washer switch(P. 2-27)4. Engine hood (P. 3-23)5. Tie down/towing hooks (
Vehicle information display warningsand indicators1. Door and trunk open warning2. Push warning (CVT models)3. Low fuel warning4. Low windshield washe
11. Engine start operation indicator (MT mod-els)12. NISSAN Intelligent Key™ insertion indicator13. NISSAN Intelligent Key™ removal indicator14. NISSA
cruise main switch indicator illuminates, thecruise control system is operational.Cruise set switch indicatorThis indicator illuminates while the vehi
Your vehicle may have two types of security sys-tems:● Vehicle security system● NISSAN Vehicle Immobilizer SystemVEHICLE SECURITY SYSTEMThe vehicle se
The alarm is activated by:● opening the door or trunk lid without usingthe key or Intelligent Key (even if the door isunlocked by releasing the door i
SWITCH OPERATIONThe windshield wiper and washer switch oper-ates when the ignition switch is placed in the ONposition.Push the lever down to operate t
To defrost the rear window glass and outsidemirrors (if so equipped), start the engine andpush the rear window defroster switch on. Therear window def
XENON HEADLIGHTS (if soequipped)WARNINGcHIGH VOLTAGE● When xenon headlights are on, theyproduce a high voltage. To prevent anelectric shock, never att
CAUTIONUse the headlights with the engine run-ning to avoid discharging the vehiclebattery.Autolight system (if so equipped)The autolight system allow
To turn on the autolight system:1. Turn the headlight switch to the AUTO posi-tions1.2. Push the push-button ignition switch to theON position.3. The
Coupe1. Rear window defroster switch (P. 2-28)2. Interior trunk lid release (P. 3-24)3. Trunk lid (P. 3-23)4. Vehicle loading (P. 9-12)5. Opener opera
CAUTIONEven though the battery saver feature au-tomatically turns off the headlights after aperiod of time, you should turn the head-light switch to t
TURN SIGNAL SWITCHTurn signals1Move the lever up or down to signal theturning direction. When the turn is com-pleted, the turn signals cancel automati
The flashers will operate with the ignition switchplaced in any position.Some state laws may prohibit the use ofthe hazard warning flasher switch whil
CAUTION● Do not use the seat heater for extendedperiods or when no one is using theseat.● Do not put anything on the seat whichinsulates heat, such as
The power outlets are for powering electricalaccessories such as cellular telephones. Theyare rated at 12 volt, 120W (10A) maximum. Theconsole outlet
Open the lower half of the console box to accessthe power outlet. Refer to “Console box” in thissection.MAP POCKETS SEATBACK POCKETS (if soequipped)Th
STORAGE POUCH (if so equipped)A storage pouch is located on the front of thedriver’s and passenger’s seats.WARNINGDo not store angular, sharp, heavy o
Front - Type ALIC1075Front - Type BLIC1105Rear (sedan)WRS0167Instruments and controls 2-39Z REVIEW COPY—2009 Altima (alt)Owners Manual (owners)—USA_En
CUP HOLDERSTo open the front cup holders, push the cupholder lid. To close, lower the cup holder lid andpush down until it clicks in place.The plastic
GLOVE BOXOpen the glove box by pulling the handle. Use themaster key when lockings1or unlockings2theglove box.WARNINGKeep glove box lid closed while d
Sedan1. Rear window defroster switch (P. 2-28)2. Interior trunk lid release (P. 3-24)3. Trunk lid (P. 3-23)4. Vehicle loading (P. 9-12)5. Opener opera
STORAGE BOX (if so equipped)COVERED STORAGE BOXPush the center of the lid to open.LIC1477Type ALIC1090Type BLIC10782-42 Instruments and controlsZ REVI
GROCERY HOOKS (if so equipped)The grocery hooks are located in the trunk andcan be used to hang a standard size plasticgrocery bag.CAUTIONDo not apply
POWER WINDOWSWARNING● Make sure that all passengers havetheir hands, etc. inside the vehicle whileit is in motion and before closing thewindows. Use t
Front passenger’s power windowswitchThe passenger’s window switch operates onlythe corresponding passenger’s window. To openthe window, push the switc
Auto-reverse functionIf the control unit detects something caught in thewindow as it is closing, the window will be imme-diately lowered.The auto-reve
To fully close the moonroof, push the switchtowards2.To open or close the moonroof part way, push theswitch in any direction while the moonroof isslid
Depending on the environment or drivingconditions, the auto-reverse function maybe activated if an impact or load similar tosomething being caught in
The lights will go off when the ignition switch isplaced in the ON position, or the driver’s door isclosed and locked.The lights will also go off afte
To turn the map lights on, press the light lens. Toturn them off, press the lens again.CAUTIONDo not use for extended periods of timewith the engine s
The HomeLinkT Universal Transceiver provides aconvenient way to consolidate the functions of upto three individual hand-held transmitters intoone buil
1. Interior trunk access (P. 1-9)2. Moonroof (if so equipped) (P. 2-46)3. Sun visors (P. 3-27)4. Interior lights, illuminated entry (P. 2-48)5. HomeLi
3. Using both hands, simultaneously press andhold both the HomeLinkT button you want toprogram and the hand-held transmitter but-ton.DO NOT release th
NOTE:When programming a garage door opener,etc., it is advised to unplug the device dur-ing the “cycling” process to prevent pos-sible damage to the g
NOTE:Following step 2, there are 30 seconds inwhich to initiate step 3.3. Firmly press and release the programmedHomeLinkT button a second time to com
3 Pre-driving checks and adjustmentsKeys...3-2NISSAN Intelligent Key™ ...3-2NISSAN Vehi
1. Two Intelligent Keys2. Mechanical keys (inside IntelligentKeys)3. Key number plateNISSAN INTELLIGENT KEY™Your vehicle can only be driven with the I
Mechanical keyThe Intelligent Key contains the mechanical key.To remove the mechanical key, release the lockknob on the back of the Intelligent Key.To
WARNING● Always have the doors locked whiledriving. Along with the use of seat belts,this provides greater safety in the eventof an accident by helpin
LOCKING WITH INSIDE LOCKKNOBTo lock the door without the key, move the insidelock knob to the lock positions1, then close thedoor.To unlock the door w
3. Do one of the following within 20 seconds ofperforming Step #2:● To change AUTO UNLOCK settings:push and hold the power door lock switchto theposit
CAUTION● Be sure to carry the Intelligent Key withyou when operating the vehicle.● Never leave the Intelligent Key in thevehicle when you leave the ve
1. Vents (P. 4-10)2. Headlight/fog light (if so equipped)/turnsignal switch (P. 2-29)3. Steering wheel switch for audio control(if so equipped)/Blueto
● Do not attach the Intelligent Key with akey holder that contains a magnet.● Do not place the Intelligent Key nearequipment that produces a magneticf
DOOR LOCKS/UNLOCKSPRECAUTION● Do not push the door handle request switchwith the Intelligent Key held in your hand asillustrated. The close distance t
Locking doors1. Move the shift selector to the P (Park) posi-tion, place the ignition switch in the LOCKposition and make sure you carry the Intelli-g
NOTE:The doors may not lock when the Intelli-gent Key is in the same hand that is oper-ating the request switch to lock the door.Put the Intelligent K
● Placing the ignition switch in the ON posi-tion.● Locking the doors with the remote controller.● Switching the room light switch to the OFFposition.
Locking doors1. Place the ignition switch in the LOCK posi-tion.2. Close all doors.3. Press thebutton on the IntelligentKey.4. The hazard warning ligh
The interior light illuminates for 15 seconds whena door is unlocked and the room light switch is inthe DOOR position.The light can be turned off with
The panic alarm stops when:● It has run for 25 seconds, or● Any button is pressed on the Intelligent Key.● Pushing the request switch on the driver or
TROUBLESHOOTING GUIDEVerify the location of all Intelligent Keys that areprogrammed for the vehicle. If another IntelligentKey is in range or inside t
WARNING●Radio waves could adversely affect elec-tric medical equipment. Those who use apacemaker should contact the electricmedical equipment manufact
20. Traction Control System (TCS) OFFswitch (if so equipped) (P. 5-25)Trunk opener (P. 3-23)Vehicle Dynamic Control (VDC) OFFswitch (if so equipped) (
As many as 4 Intelligent Keys can be registeredand used with one vehicle. For information aboutthe purchase and use of additional IntelligentKeys, con
Locking doors1. Place the ignition switch in the LOCK posi-tion.2. Close all doors.3. Press thebutton on the IntelligentKey.4. The hazard warning ligh
The interior light illuminates for 15 seconds whena door is unlocked and the room light switch is inthe DOOR position.The light can be turned off with
The panic alarm stops when:● It has run for 25 seconds, or● Any button is pressed on the Intelligent Key.● Pushing the request switch on the driver or
TROUBLESHOOTING GUIDEVerify the location of all Intelligent Keys that areprogrammed for the vehicle. If another IntelligentKey is in range or inside t
s1Pull the hood lock release handle locatedbelow the driver’s side instrument panel; thehood springs up slightly.s2Lift the lever at the front of the
● Closely supervise children when theyare around cars to prevent them fromplaying and becoming locked in thetrunk where they could be seriously in-jur
To open the trunk from the inside, pull the illumi-nated release handle until the lock releases andpush up on the trunk lid. The release handle ismade
WARNING● Gasoline is extremely flammable andhighly explosive under certain condi-tions. You could be burned or seriouslyinjured if it is misused or mi
TILT OPERATIONPull the levers1all the way toward you andadjust the steering wheel up or downs2to thedesired position. Lock the wheel by releasing thel
QR25DE engine1. Power steering fluid reservoir (P. 8-13)2. Engine oil filler cap (P. 8-9)3. Brake fluid reservoir/Clutch fluidreservoir (M/T model) (P
s3Slide the extension sun visor (if so equipped)in or out as needed.CAUTIONDo not store the sun visor before returningthe extension to its original po
AUTOMATIC ANTI-GLAREREARVIEW MIRROR (if so equipped)The inside mirror is designed so that it automati-cally dims according to the intensity of the hea
Manual folding outside mirrors (if soequipped)Pull the outside mirror toward the door to fold it.WPD00563-30 Pre-driving checks and adjustmentsZ REVIE
Pre-driving checks and adjustments 3-31MEMO
4 Monitor, climate, audio, phone and voicerecognition systemsControl panel buttons (if so equipped) ...4-2Setting up the start-up screen .
BluetoothT Hands-Free Phone System withNavigation System (if so equipped) ...4-61Regulatory Information ...4-62Voi
WARNING● Do not disassemble or modify this sys-tem. If you do, it may result in accidents,fire, or electrical shock.● Do not use this system if you no
When you use this system, make sure the engineis running.If you use the system with the engine notrunning (ignition ON or ACC) for a longtime, it will
Display settingsTouch the “Display” key. The display screen willappear.Display/brightness/contrast:Touch the “–” key or the “+” key to adjust thebrigh
ClockAdjusting the time:The following display will appear when pressingthe SETUP button, then touching the “Clock” key.On-screen Clock:When this item
VQ35DE engine1. Power steering fluid reservoir (P. 8-13)2. Engine oil filler cap (P. 8-9)3. Brake fluid reservoir/Clutch fluidreservoir (M/T model) (P
After selection, touch the “Back” key the Clockscreen will appear.Pacific zone has been set as the initial (default)setting.Beep settingTouch the “Vol
Select Language:Touch the “Select Language” key. From the fol-lowing display, select the English “ON” key or theFrançais “ON” key for your language pr
When the shift selector is shifted into the R(Reverse) position, the monitor display shows theview directly to the rear of the vehicle.WARNING● The sy
ADJUSTING THE SCREENTo adjust the quality of the screen, press theSETUP button.● To adjust the Brightness, Tint, Contrast, Dis-play ON/OFF and Color o
Adjust air flow direction by moving the ventslides.Open or close the vents by using the dial. Movethe dial toward theto open the vents ortoward theto
WARNING● The air conditioner cooling function op-erates only when the engine is running.● Do not leave children or adults whowould normally require th
— Air flows from center and sidevents and foot outlets.— Air flows mainly from foot outlets.— Air flows from defroster outletsand foot outlets.— Air f
3. Turn the temperature control dial to the de-sired position between the middle and thehot position.● To quickly remove ice or fog from the win-dows,
● For quick cooling when the outside tem-perature is high, push thebutton tothe ON position. Be sure to return theto the OFF position for normal cooli
WHA1179 WHA1180Monitor, climate, audio, phone and voice recognition systems 4-15Z REVIEW COPY—2009 Altima (alt)Owners Manual (owners)—USA_English (nna
WarninglightName PageorAnti-lock BrakingSystem (ABS) warn-ing light2-11orBrake warning light 2-11Charge warninglight2-11Continuously Vari-able Transmi
WHA1181 WHA11824-16 Monitor, climate, audio, phone and voice recognition systemsZ REVIEW COPY—2009 Altima (alt)Owners Manual (owners)—USA_English (nna
WHA1183Monitor, climate, audio, phone and voice recognition systems 4-17Z REVIEW COPY—2009 Altima (alt)Owners Manual (owners)—USA_English (nna)02/03/0
1. Driver temperature control dial2. Air flow control buttons3. Passenger temperature control dial4. DUAL button5. Rear defrost button6. Front window
● The temperature of the passenger compart-ment will be maintained automatically. Airflow distribution, fan speed and A/C on/offare also controlled au
OPERATING TIPS● When the engine coolant temperature andoutside air temperature are low, the air flowfrom the foot outlets may not operate for amaximum
RADIOWith the ignition placed in the ACC or ON posi-tion, press the PWR (power)/VOL (volume) knobto turn the radio on. If you listen to the radio with
SATELLITE RADIO RECEPTION (if soequipped)When the satellite radio is used for the first timeor the battery has been replaced, the satelliteradio may n
● Do not expose the CD to direct sun-light.● CDs that are in poor condition or aredirty, scratched or covered with finger-prints may not work properly
● Sampling frequency — Sampling frequencyis the rate at which the samples of a signalare converted from analog to digital (A/Dconversion) per second.●
Specification chart:Supported media CD, CD-R, CD-RWSupported file systems ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (
1 Safety—Seats, seat belts andsupplemental restraint systemSeats ...1-2Front manual seat adjustment ...
Troubleshooting guide:Symptom Cause and CountermeasureCannot playCheck if the disc was inserted correctly.Check if the disc is scratched or dirty.Chec
1. SEEK/TRACK button2. CD insert slot3. TUNE/FF·REW button4.CD eject button5. AUDIO button (BASS, TREBLE, FADEand BALANCE)6. CLOCK button7. AUX IN jac
AUDIO button (Bass, Treble, Fade and Bal-ance)Press the AUDIO button to change the mode asfollows:Bass → Treble → Fade → Balance → BeepON/OFF → Audio
When the RADIO button is pressed while theignition switch is in the ACC or ON position, theradio will come on at the station last played.If a compact
Each time the button is pressed, the CD ad-vances 1 additional track. The track number ap-pears in the display window. (When the last trackon the comp
1. SEEK/TRACK button2. CD insert slot3. TUNE/FF·REW button4.CD eject button5. AUDIO button (BASS, TREBLE, FADE,SSV, BALANCE and BEEPS)6. CLOCK button7
operational then pressing the RADIO button willswitch between FM and AM bands.Audio main operationPWR/VOL control knobPlace the ignition switch in the
CD display modeTo change the text displayed while playing a CDwith text, press the DISP button. The DISP buttonwill allow you to scroll through CD tex
TUNE/FF·REW (tuning)button:Press the TUNE/FF·REW buttonorfor manual tuning. To move quickly through thechannels, hold the tuning buttons down.SEEK (tu
The slot numbers (1 – 6) will illuminate on thedisplay when CDs are loaded into the changer.CD button:When the CD button is pressed with the systemoff
Welcome to the growing family of new NISSANowners. This vehicle is delivered to you withconfidence. It was produced using the latesttechniques and str
WARNING● Do not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt will notbe against your body. In an acc
SCAN button:1 Disc, All TracksWhile listening to a CD, press the SCAN buttonto preview the first 10 seconds of each track onthe CD playing. Pressing t
1. RADIO* button2. Touch-screen keys (vary depending onwhat function is selected)3. SEEK/TRACK button4. TUNE·FOLDER and AUDIO controlknob (BASS, TREBL
FM/AM/SAT RADIO WITHCOMPACT DISC (CD) CHANGER (ifso equipped)For all operation precautions, see “Audio opera-tion precautions” earlier in this section
CD display modeWhile listening to a CD or an MP3/WMA CDcertain text might be displayed (when CD en-coded with text is being used).Depending on how the
SEEK/TRACK (tuning)button:Press the SEEK/TRACK buttonorfor less than 1.5 seconds to tune from high to lowor low to high frequencies and stop at the ne
The slot numbers (1 – 6) will illuminate on thedisplay when CDs are loaded into the changer.When one of the CD changer (1 – 6) buttons ispressed with
MP3 CD:1 DISC RPT → 1 FOLDER RPT → 1 TRACKRPT1 DISC RPT: The disc that is currently playing willbe repeated.1 TRACK RPT: The track that is currently p
CD CARE AND CLEANING● Handle a CD by its edges. Do not bend thedisc. Never touch the surface of the disc.● Always place the discs in the storage casew
1. Source select and Power on switch2. Tuning switch3. Volume control switch1. Source select and Power on switch2. Tuning switch3. Volume control swit
Seek tuning (radio):Push the tuning switchor for morethan 1.5 seconds to seek the next or previousradio station.Next/Previous track (CD):Push the tuni
Forward and backwardPull the center of the bar up and hold it while youslide the seat forward or backward to the desiredposition. Release the bar to l
CAUTION● Keep the antenna as far away as pos-sible from the electronic controlmodules.● Keep the antenna wire more than 8 in(20 cm) away from the elec
Your NISSAN is equipped with the BluetoothTHands-Free Phone System. If you have a com-patible BluetoothT enabled cellular phone, youcan set up the wir
– Your cellular phone is locked to prevent itfrom being dialed.● When the radio wave condition is not idealor ambient sound is too loud, it may bediff
Operating tipsTo get the best performance out of the NISSANVoice Recognition system, observe the following:● Keep the interior of the vehicle as quiet
● Numbers can be spoken in small groups.The system will prompt you to continue en-tering digits, if desired.Example: 1-800-662-6200– “One eight zero z
PHONE/ENDPress thebutton to cancel a VRsession or end a call.GETTING STARTEDThe following procedures will help you getstarted using the BluetoothT Han
4. Say: “New phone”sC. The system acknowl-edges the command and asks you to initiatepairing from the phone handsetsD.The pairing procedure of the cell
For additional command options, see “List ofvoice commands” later in this section.LIST OF VOICE COMMANDSMain Menu“Call” or “Call International”“Phone
If a redial number does not exist, the systemannounces, “There is no number to redial” andends the VR session.“Call back”sDUse the Call Back command t
NOTE:Each phone has its own separate phonebook. You cannot access Phone A’s phonebook if you are currently connected withPhone B.“New entry”sAUse the
FRONT POWER SEATADJUSTMENT (if so equipped fordriver’s seat)Operating tips● The power seat motor has an auto-resetoverload protection circuit. If the
The transfer procedure varies according to eachcellular phone. See the cellular phone Owner’sManual for details. You can also visitwww.nissanusa.com/b
“Setup”Main Menu“Setup”“Pair Phone”sA“List Phone”sB“Select Phone”sC“Change Priority”sD“Delete Phone”sE“Select Ringtone”sF“Bluetooth Off”sGUse the Setu
and you change the priority level of Phone C toLevel 1, then:Priority Level 1 = Phone CPriority Level 2 = Phone BPriority Level 3 = Phone A“Delete pho
For information on selecting a different lan-guage, see “Choosing a language” earlier inthis section.6. Voice memory A or memory B is selectedautomati
TROUBLESHOOTING GUIDEThe system should respond correctly to all voicecommands without difficulty. If problems are en-countered, try the following solu
WARNING● Use a phone after stopping your vehiclein a safe location. If you have to use aphone while driving, exercise extremecaution at all times so f
module when the ignition switch is turned to theON position with the paired cellular phone turnedon and carried in the vehicle.You can register up to
2. this device must accept any interference,including interference that may cause un-desired operation of the device.IC Regulatory information– Operat
PHONE DOWNLOADUp to 70 phone numbers can be stored in thephonebook.1. Press the SETUP button, then touch the“Phone” key.2. Touch the “Phonebook” key.3
5. Operate the cellular phone to send a per-son’s name and phone number from thememory of the cellular phone. The memorysending procedure from the cel
CAUTION● Do not operate the power recline switchwhen the seatback has been manuallyreleased using the upper seatback re-lease levers1. Doing so can da
MAKING A CALLTo make a call, follow the procedure below.1. Press the phonebutton on the steer-ing wheel switches. The phone screen willappear on the d
Hold Call:Continue to hold call.Reject Call:Reject an incoming call.To finish the call, follow one of the procedureslisted below:a. Touch the “Reject
PHONE SETTINGTo set up the hands-free phone system to yourpreferred settings, press the SETUP button, thentouch the “Phone” key on the display.Phonebo
Bluetooth Setup:See the following information for each item.● Bluetooth Hands-Free:If this item is turned off, the connection be-tween the cellular ph
Giving voice commands1. Press the button.2. The system announces: “Please say a com-mand”3. After the tone sounds and the face icon ofthe display chan
● say “Dial” or “Phone dial” the system willrespond with “Please say the first group ofnumbers”, then say:– “one eight oh oh six six two six two oh oh
● “PHONEBOOK <voicetag> ”Shows the specified “voicetag” entry in the“phone book” and dials the phone numberregistered in the specified “voicetag
TROUBLESHOOTING GUIDEThe system should respond correctly to all voicecommands without difficulty. If problems are en-countered, follow the solutions g
4-74 Monitor, climate, audio, phone and voice recognition systemsMEMO
5 Starting and drivingPrecautions when starting and driving...5-2Exhaust gas (carbon monoxide) ...5-2Three-way catalyst...
Seat lifter (if so equipped for driver’sseat)Pull the lever up or push down to adjust the angleand height of the seat cushion.Lumbar support (if so eq
WARNING● Do not leave children or adults whowould normally require the assistanceof others alone in your vehicle. Petsshould also not be left alone. T
CAUTION● Do not use leaded gasoline. Depositsfrom leaded gasoline will seriously re-duce the three-way catalyst’s ability tohelp reduce exhaust pollut
Additional information:● The TPMS does not monitor the tirepressure of the spare tire.● The TPMS will activate only when the vehicleis driven at speed
● When a spare tire is mounted or a wheelis replaced, tire pressure will not beindicated, the TPMS will not functionand the low tire pressure warning
OFF-ROAD RECOVERYWhile driving, the right side or left side wheelsmay unintentionally leave the road surface. If thisoccurs, maintain control of the v
DRINKING ALCOHOL/DRUGS ANDDRIVINGWARNINGNever drive under the influence of alcoholor drugs. Alcohol in the bloodstream re-duces coordination, delays r
The ignition switch is equipped with an anti-theftsteering lock device.The ignition lock is designed so that the ignitionswitch position cannot be swi
If the battery of the Intelligent Key is almost dis-charged, the guide lightsAof the Intelligent Keyport blinks and the indicator appears on the ve-hi
● Make sure the area around the vehicle isclear.● Check fluid levels such as engine oil, cool-ant, brake fluid, and window washer fluid asfrequently a
4. Warm-upAllow the engine to idle for at least 30 sec-onds after starting. Do not race the enginewhile warming it up. Drive at moderatespeed for a sh
Entry to the rear seat from outside ofthe vehicle on the front passenger side(Coupe)Pull the seat recliner levers1to the uppermostposition folding the
The CVT is designed so the foot brakepedal MUST be depressed before shiftingfrom P (Park) to any drive position whilethe ignition switch is in the ON
R (Reverse):CAUTIONTo prevent transmission damage, use theP (Park) or R (Reverse) position only whenthe vehicle is completely stopped.Use the R (Rever
● The transmission will automatically down-shift the gears. (For example, if you select the3rd range, the transmission will shift downbetween the 3rd
To move the shift selector, complete the followingprocedure:1. Push the ignition switch to the LOCK posi-tion.2. Apply the parking brake.3. Remove the
MANUAL TRANSMISSION (if soequipped)WARNING● Do not downshift abruptly on slipperyroads. This may cause a loss of control.● Do not over-rev the engine
For normal acceleration in low altitude areas (lessthan 4,000 ft [1219 m]):For QR25DE:GEAR CHANGE ACCEL shiftpoint MPH(km/h)CRUISE shiftpoint MPH(km/h
WARNING● Be sure the parking brake is fully re-leased before driving. Failure to do socan cause brake failure and lead to anaccident.● Do not release
1. CANCEL switch2. ACCEL/RES switch3. COAST/SET switch4. ON/OFF switchPRECAUTIONS ON CRUISECONTROL● If the cruise control system malfunctions, itcance
The cruise control is automatically canceled andthe SET light in the instrument panel goes out if:● you depress the brake or clutch pedal whilepushing
● Accelerate slowly and smoothly. Maintaincruising speeds with a constant acceleratorposition.● Drive at moderate speeds on the highway.Driving at hig
Pull the upper seatback release levers1to theuppermost position, folding the seatback forwards2, releasing the seat track.Slide the entire seat forwar
WARNING● Do not stop or park the vehicle overflammable materials such as dry grass,waste paper or rags. They may igniteand cause a fire.● Safe parking
The power assisted steering uses a hydraulicpump, driven by the engine, to assist steering.If the engine stops or the drive belt breaks, youwill still
To dry the brakes, drive the vehicle at a safespeed while lightly pressing the brake pedal toheat up the brakes. Do this until the brakes returnto nor
Normal operationThe ABS operates at speeds above3-6MPH(5- 10 km/h). The speed varies according to roadconditions.When the ABS senses that 1 or more wh
● When driving on extremely inclined sur-faces such as higher banked corners,the Traction Control System may notoperate properly and theindica-tor lig
● Do not modify the vehicle’s suspension.If suspension parts such as shock ab-sorbers, struts, springs, stabilizer bars,bushings and wheels are not NI
DRAINING OF COOLANT WATERIf the vehicle is to be left outside without anti-freeze, drain the cooling system, including theengine block. Refill before
ENGINE BLOCK HEATER (if soequipped)WARNING● Do not use your engine block heaterwith an ungrounded electrical systemor a 2-pronged adapter. You can be
5-30 Starting and drivingMEMO
6 In case of emergencyFlat tire ...6-2Tire Pressure Monitoring System (TPMS)...6-2Changing a flat tire
Exiting from the rear seat on thedriver’s side, using the upper seatbackrelease lever (coupe)Pull the upper seatback release levers1to theuppermost po
TIRE PRESSURE MONITORINGSYSTEM (TPMS)This vehicle is equipped with the Tire PressureMonitoring System (TPMS). It monitors tire pres-sure of all tires
WARNING● Make sure the parking brake is securelyapplied and the manual transmission isshifted into R (Reverse), or the CVT isshifted into P (Park).● N
Turn the clamp to remove the spare tire. Removethe spare tire.Removing the bolt-on wheel cover (ifso equipped)CAUTIONDo not use your hands to pry off
Jacking up vehicle and removing thedamaged tireWARNING● Never get under the vehicle while it issupported only by the jack. If it is nec-essary to work
Always refer to the proper illustrations for thecorrect placement and jack-up points for yourspecific vehicle model and jack type.Carefully read the c
4. Lower the vehicle slowly until the tiretouches the ground. Then, with the wheelnut wrench, tighten the wheel nuts securelyin the sequence illustrat
● Whenever working on or near a battery,always wear suitable eye protectors (forexample, goggles or industrial safetyspectacles) and remove rings, met
CAUTION● Always connect positive (1) to positive(1) and negative (2) to body ground (forexample, strut mounting bolt, enginelift bracket, etc.) — not
3. Get out of the vehicle. Look and listen forsteam or coolant escaping from the radiatorbefore opening the hood. (If steam or cool-ant is escaping, t
For information about towing your vehicle behinda recreational vehicle (RV), refer to “Flat towing”in the “Technical and consumer information” sec-tio
1. Open the access cover on the rear parcelshelf.2. Push down on the button on the rear parcelshelf.3. Fold down the passenger’s side seatback.WARNING
CAUTION● Never tow Continuously Variable Trans-mission (CVT) models with the frontwheels on the ground or four wheels onthe ground (forward or backwar
WARNING● Stand clear of a stuck vehicle.● Do not spin your tires at high speed.This could cause them to explode andresult in serious injury. Parts of
6-14 In case of emergencyMEMO
7 Appearance and careCleaning exterior ...7-2Washing ...7-2Waxing ...
In order to maintain the appearance of your ve-hicle, it is important to take proper care of it.To protect the paint surfaces, please wash yourvehicle
REMOVING SPOTSRemove tar and oil spots, industrial dust, insects,and tree sap as quickly as possible from thesurface of the paint to avoid lasting dam
● Do not apply wheel cleaners to thewheels when they are hot. The wheeltemperature should be the same as am-bient temperature.● Rinse the wheel to com
CAUTION● Never use benzine, thinner or any simi-lar material.● Small dirt particles can be abrasive anddamaging to leather surfaces andshould be remov
SEAT BELTSThe seat belts can be cleaned by wiping themwith a sponge dampened in a mild soap solution.Allow the belts to dry completely in the shadebef
CAUTION● NEVER remove dirt, sand or other de-bris from the passenger compartmentby washing it out with a hose. Removedirt with a vacuum cleaner or bro
Center armrest (if so equipped)Pull the armrest down until it is horizontal.HEAD RESTRAINTSWARNINGHead restraints supplement the other ve-hicle safety
7-8 Appearance and careMEMO
8 Maintenance and do-it-yourselfMaintenance requirements...8-2General maintenance ...8-2Explanation
Your NISSAN has been designed to have mini-mum maintenance requirements with long ser-vice intervals to save you both time and money.However, some day
When driving in areas using road salt or othercorrosive materials, check lubrication frequently.Lights* Clean the headlights on a regular basis.Make s
and are installed securely. Check the belt web-bing for cuts, fraying, wear or damage.Steering wheel Check for changes in the steer-ing system, such a
When performing any inspection or maintenancework on your vehicle, always take care to preventserious accidental injury to yourself or damage tothe ve
QR25DE engine1. Power steering fluid reservoir2. Engine oil filler cap3. Brake fluid reservoir/Clutch fluidreservoir (M/T model)4. Air cleaner5. Fuse
VQ35DE engine1. Power steering fluid reservoir2. Engine oil filler cap3. Brake fluid reservoir/Clutch fluidreservoir (M/T model)4. Air cleaner5. Fuse
The engine cooling system is filled at the factorywith Genuine NISSAN Long LifeAntifreeze/Coolant to provide year-round anti-freeze and coolant protec
CHANGING ENGINE COOLANTA NISSAN dealer can change the engine coolant.The service procedure can be found in theNISSAN Service Manual.Improper servicing
This manual includes information for all optionsavailable on this model. Therefore, you may findsome information that does not apply to yourvehicle.Al
Components1. Head restraint2. Adjustment notches3. Lock knob4. StalksAdjustmentAdjust the head restraint so the center is levelwith the center of the
5. Remove the dipstick again and check the oillevel. It should be between the H (High) andL (Low) markssB. This is the normal oper-ating oil level ran
5. Remove the drain plugsBwith a wrench byturning it counterclockwise and completelydrain the oil.If the oil filter is to be changed, remove andreplac
CHANGING ENGINE OIL FILTER1. Park the vehicle on a level surface and applythe parking brake.2. Turn the engine off.3. Place a large drain pan under th
CAUTION● Use only Genuine NISSAN CVT FluidNS-2-V. Do not mix with other fluids.● Using transmission fluid other thanGenuine NISSAN CVT Fluid NS-2-V wi
For further brake and clutch fluid specificationinformation, refer to “Capacities and recom-mended fuel/lubricants” in the “Technical andconsumer info
WINDOW WASHER FLUIDRESERVOIRFill the window washer fluid reservoir periodically.Add window washer fluid when the low windowwasher fluid warning light
● Do not operate the vehicle if the fluid inthe battery is low. Low battery fluid cancause a higher load on the batterywhich can generate heat, reduce
Vehicles operated in high temperatures or undersevere conditions require frequent checks of thebattery fluid level.JUMP STARTINGIf jump starting is ne
1. Power steering fluid pump2. Generator3. Air conditioner4. Crank pulleyREPLACING SPARK PLUGSIridium-tipped spark plugs (if soequipped)It is not nece
The air cleaner filter should not be cleaned andreused. Replace it according to the maintenancelog shown in the “NISSAN Service and Mainte-nance Guide
To lower, push and hold the lock knob and pushthe head restraint down.RemovalUse the following procedure to remove the ad-justable head restraints.1.
CLEANINGIf your windshield is not clear after using thewindshield washer or if a wiper blade chatterswhen running, wax or other material may be onthe
If you wax the surface of the hood, be careful notto let wax get into the washer nozzlesA. This maycause clogging or improper windshield washeroperati
Two types of fuses are used. TypesAis used inthe fuse boxes in the engine compartment. TypesBis used in the passenger compartment fusebox.Type A fuses
3. Remove the fuse box cover by pushing thetab and lifting the cover up.4. Remove the fuse with the fuse puller. Thefuse puller is located in the cent
PASSENGER COMPARTMENTCAUTIONNever use a fuse of a higher or loweramperage rating than specified on thefuse box cover. This could damage theelectrical
CAUTIONBe careful not to allow children to swallowthe battery or removed parts.Type BLDI0456WDI0567BATTERY REPLACEMENTMaintenance and do-it-yourself 8
NISSAN INTELLIGENT KEY™Replace the battery in the Intelligent Key as fol-lows:1. Remove the mechanical key from the Intelli-gent Key.2. Insert a small
HEADLIGHTSReplacing the xenon headlight bulb (ifso equipped)WARNINGcHIGH VOLTAGEWhen xenon headlights are on, they pro-duce a high voltage. To prevent
EXTERIOR AND INTERIOR LIGHTSItem Wattage (W) Bulb No.*1Headlight assembly *2Low (Halogen) 55 H11Low (Xenon) 35 D2RHigh 65 H9Park 8 168Turn 27 3457NAKS
Coupe1. Mirror-mounted turn signal light(if so equipped)2. Interior light3. Map light4. Headlamp assembly5. Fog light (if so equipped)6. Step light7.
Front-seat Active Head RestraintsThe Active Head Restraint moves forward utiliz-ing the force that the seatback receives from theoccupant in a rear-en
Sedan1. Rear map light2. Front map light3. Step light4. Headlamp assembly5. Fog light (if so equipped)6. High-mount stoplight (if so equipped)7. Trunk
Replacement proceduresAll other lights are either type A, B, C or D. Whenreplacing a bulb, first remove the lens, lightand/or cover.Indicates bulb rem
Use a cloths1to protect the housing. Use a cloths1to protect the housing.Map lightLDI0571Interior lightWDI06328-32 Maintenance and do-it-yourselfZ REV
Rear combination lightTo access the bulbs in the rear combination light:s1Remove the fasteners. Carefully push backthe carpet.s2Remove the 2 nuts and
If you have a flat tire, see “Flat tire” in the“In case of emergency” section of thismanual.TIRE PRESSURETire Pressure Monitoring System(TPMS)This veh
Incorrect tire pressure, including un-der inflation, may adversely affecttire life and vehicle handling.WARNING● Improperly inflated tires can failsud
Tire and loading information labels1Seating capacity: The maximum num-ber of occupants that can be seatedin the vehicle.s2Vehicle load limit: See load
Checking tire pressure1. Remove the valve stem cap from thetire.2. Press the pressure gauge squarelyonto the valve stem. Do not press toohard or force
Size Cold Tire Inflation Pres-sureFront Original Tire P215/60/R16 220 kPa, 32 PSIP215/55R17 230 kPa, 33 PSIP235/45R18Rear Original Tire P215/60R16 220
s1Tire size (example: P215/65R15 95H)1. P: The “P” indicates the tire is de-signed for passenger vehicles (not alltires have this information).2. Thre
PRECAUTIONS ON SEAT BELTUSAGEIf you are wearing your seat belt properly ad-justed and you are sitting upright and well back inyour seat with both feet
s2TIN (Tire Identification Number) for anew tire (example: DOT XX XX XXXXXXX)1. DOT: Abbreviation for the “Depart-ment Of Transportation”. The symbolc
s7The word “radial”The word “radial” is shown if the tire hasradial structure.s8Manufacturer or brand nameManufacturer or brand name is shown.Other Ti
studded tires. Skid and traction capabilities ofstudded snow tires on wet or dry surfaces may bepoorer than that of non-studded snow tires.TIRE CHAINS
CHANGING WHEELS AND TIRESTire rotationNISSAN recommends rotating the tiresevery 7,500 miles (12,000 km).See “Flat tire” in the “In case of emer-gency”
● The original tires have built-intread wear indicators. When thewear indicators are visible, thetire(s) should be replaced.● Tires degrade with age a
● Do not install a damaged or deformedwheel or tire even if it has been re-paired. Such wheels or tires could havestructural damage and could fail wit
● Tire tread of the TEMPORARY USEONLY spare tire will wear at a faster ratethan the standard tire. Replace thespare tire as soon as the tread wearindi
9 Technical and consumer informationCapacities and recommended fuel/lubricants ...9-2Fuel recommendation ...9-3Engine oi
The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the proceduredescribed in the
FUEL RECOMMENDATIONFor 2.5L engineUse unleaded regular gasoline with an octanerating of at least 87 AKI (Anti-Knock Index) num-ber (Research octane nu
WARNING● Every person who drives or rides in thisvehicle should use a seat belt at alltimes. Children should be properly re-strained in the rear seat
If any driveability problems such as engine stall-ing and difficult hot-starting are experienced afterusing oxygenate-blend fuels, immediatelychange t
ENGINE OIL AND OIL FILTERRECOMMENDATIONSSelecting the correct oilIt is essential to choose the correct grade, qualityand viscosity engine oil to ensur
Your engine was filled with a high-quality engineoil when it was built. You do not have to changethe oil before the first recommended changeinterval.
ENGINEModel QR25DE VQ35DEType Gasoline, 4-cycle, DOHC Gasoline, 4-cycle, DOHCCylinder arrangement 4-cylinder in-line 6-cylinder, V-block, Slanted at 6
WHEELS AND TIRESWheel type Size Offset in (mm)Aluminum/Steel 16 x 7JJ 1.77 (45)Aluminum 17 x 7 1/2JJ 1.77 (45)Aluminum 18 x 7.5JJ 1.77 (45)T type (Spa
When planning to drive your NISSAN ve-hicle in another country, you should first findout if the fuel available is suitable for your vehi-cle’s engine.
ENGINE SERIAL NUMBERThe number is stamped on the engine as shown.F.M.V.S.S./C.M.V.S.S.CERTIFICATION LABELThe Federal/Canadian Motor Vehicle SafetyStan
EMISSION CONTROLINFORMATION LABELThe emission control information label is at-tached to the underside of the hood as shown.TIRE AND LOADING INFORMATIO
Use the following steps to mount the front licenseplate:s1Make a shallow hole in each plastic finisherat the location mark (small dimple) using a0.31
● GVW (Gross Vehicle Weight) - curbweight plus the combined weight ofpassengers and cargo.● GVWR (Gross Vehicle Weight Rat-ing) - maximum total combin
WARNING● Always route the shoulder belt overyour shoulder and across your chest.Never put the belt behind your back,under your arm or across your neck
Steps for determining correct loadlimit1. Locate the statement “The combinedweight of occupants and cargoshould never exceed XXX kg or XXXlbs” on your
5. Determine the combined weight ofluggage and cargo being loaded onthe vehicle. That weight may notsafely exceed the available cargo andluggage load
WARNINGOverloading or improper loading of atrailer and its cargo can adversely affectvehicle handling, braking and perfor-mance and may lead to accide
Temperature conditions can also affect towing.For example, towing a heavy trailer in high outsidetemperatures on graded roads can affect engineperform
Towing capacities are calculated assuming abase vehicle with driver and any options requiredto achieve the rating. Additional passengers,cargo and/or
Always verify that available capacities are withinthe required ratings.TOWING LOAD/SPECIFICATIONTOWING LOAD / SPECIFICATIONUNIT: lb (kg)MAXIMUM TOWING
You may add Class I trailer hitch equipment thathas a 2,000 lb (909 kg) maximum weight rating tothe vehicle, but your vehicle is only capable oftowing
WARNINGNever connect a trailer brake system di-rectly to the vehicle brake system.When towing a trailer load of 3,500 lbs.(1587 kg) or more, trailers
● Always drive your vehicle at a moderatespeed.● When backing up, hold the bottom of thesteering wheel with one hand. Move yourhand in the direction i
2. When the trailer sway stops, gently apply thebrakes and pull to the side of the road in asafe area.3. Try to rearrange the trailer load so it is ba
CHILD SAFETYChildren need adults to help protect them.They need to be properly restrained.In addition to the general information in thismanual, child
Manual Transmission● Always tow with the manual transmission inNeutral.● After towing 500 miles (805 km), start andidle the engine with the transmissi
WARNINGThe temperature grade for this tire is es-tablished for a tire that is properly inflatedand not overloaded. Excessive speed,under-inflation, or
Due to legal requirements in some states andCanadian Provinces, your vehicle may be re-quired to be in what is called the “ready condi-tion” for an In
This vehicle is equipped with an Event Data Re-corder (EDR). The main purpose of an EDR is torecord, in certain crash or near crash-like situa-tions,
For CanadaTo purchase a copy of a genuine NISSAN Ser-vice Manual or Owner’s Manual please contactyour nearest NISSAN dealer. For the phone num-ber and
10 IndexAAir bag (See supplemental restraintsystem) ...1-43Air bag systemFront (See supplemental front impactair bag system) ...
Clock ...4-5, 4-28, 4-32, 4-38(models with navigation system) ...4-5(models without navigationsystem) ...4-28, 4-32Clock set
F.M.V.S.S. certification label ...9-10Fog light switch ...2-33Front air bag system(See supplemental restraint system) ...1-52Fr
Vehicle identification number (VIN) plate . .9-9Warning labels (for SRS)...1-58Language setting ...4-6LATCH (Lower Anchors and Te
Rear power windows ...2-45PrecautionsMaintenance precautions ...8-5Precautions on childrestraints...1-23, 1-33, 1-39Precautio
80 lbs (36 kg). A booster seat should be used toobtain proper seat belt fit.NISSAN recommends that a child be placed in acommercially available booste
SwitchAutolight switch ...2-30Automatic power window switch ...2-45Fog light switch ...2-33Hazard warning flasher switch ...
Warning labels (for SRS)...1-58Warning/indicator lights and audiblereminders ...2-10Warning lights...2-10Washer s
RECOMMENDED FUEL:For 2.5L engineUse unleaded regular gasoline with an octanerating of at least 87 AKI (Anti-Knock Index) num-ber (Research octane numb
2009 NISSAN ALTIMA 2009 ALTIMAOWNER'S MANUALL32-DPrinting : May 2009 (10)Publication No.: OM9E-0L32U2Printed in U.S.A.For your safety, read
Fastening the seat belts1. Adjust the seat. See “Seats” earlier in thissection.s2Slowly pull the seat belt out of the retractorand insert the tongue i
The Emergency Locking Retractor (ELR) modeallows the seat belt to extend and retract to allowthe driver and passengers some freedom ofmovement in the
BLUETOOTHt is atrademark owned byBluetooth SIG, Inc.,U.S.A. and licensed toVisteon and XanaviInformaticsCorporation.XM Radiot requiressubscription, so
Shoulder belt height adjustment(Sedan, front seats)The shoulder belt anchor height should be ad-justed to the position best for you. (See “Precau-tion
WARNING● Only NISSAN seat belt extenders, madeby the same company which made theoriginal equipment seat belts, shouldbe used with NISSAN seat belts.●
WARNING● Infants and small children should al-ways be placed in an appropriate childrestraint while riding in the vehicle.Failure to use a child restr
● When your child restraint is not in use,keep it secured with the LATCH systemor a seat belt to prevent it from beingthrown around in case of a sudde
LATCH lower anchor point locationsThe LATCH anchors are located at the rear of theseat cushion near the seatback. A label is at-tached to the seatback
LATCH child restraints generally require the useof a top tether strap. See “Top tether strap childrestraint” later in this section for installation in
First, secure the child restraint with the LATCHSystem (rear outboard seating positions only) orthe seat belt, as applicable.s1Flip up the anchor cove
1. If the rear seat cushion has a flaps1, pull theflap down to allow access to the anchorss2.2. Position the child restraint on the seat. Al-ways foll
5. For child restraints that are equipped withwebbing mounted attachments, remove anyadditional slack from the anchor attach-ments. Press downward and
1. If the rear seat cushion has a flaps1, pull theflap down to allow access to the anchorss2.2. Position the child restraint on the seat. Al-ways foll
NISSAN CARES...Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NIS
4. For child restraints that are equipped withwebbing mounted attachments, remove anyadditional slack from the anchor attach-ments. Press downward and
CHILD RESTRAINT INSTALLATIONUSING THE SEAT BELTSWARNING● Even with the NISSAN Advanced AirBag System, never install a rear-facingchild restraint in th
2. Position the child restraint on the seat. Al-ways follow the child restraint manufactur-er’s instructions.The back of the child restraint should be
5. Allow the seat belt to retract. Pull up on theshoulder belt to remove any slack in the belt.6. Remove any additional slack from the seatbelt; press
the belt holds the restraint in place. If therestraint is not secure, tighten the belt asnecessary, or put the restraint in anotherseat and test it ag
2. Route the seat belt tongue through the childrestraint and insert it into the buckle until youhear and feel the latch engage. Be sure tofollow the c
5. Remove any additional slack from the childrestraint; press downward and rearwardfirmly in the center of the child restraint tocompress the vehicle
PRECAUTIONS ON BOOSTERSEATSWARNING● Infants and small children should al-ways be placed in an appropriate childrestraint while riding in the vehicle.F
● After placing the child in the boosterseat and fastening the seat belt, makesure the shoulder portion of the belt isaway from the child’s face and n
All U.S. states and Canadian provinces orterritories require that infants and smallchildren be restrained in an approved childrestraint at all times w
Table ofContentsIllustrated table of contentsSafety—Seats, seat belts and supplemental restraint systemInstruments and controlsPre-driving checks and
3. The booster seat should be positioned onthe vehicle seat so that it is stable. If neces-sary, adjust or remove the head restraint toobtain the corr
6. Follow the warnings, cautions and instruc-tions for properly fastening a seat beltshown in “Three-point seat belt with retrac-tor” earlier in this
Roof-mounted curtain side-impact supple-mental air bag system: This system can helpcushion the impact force to the head of occu-pants in front and rea
● The driver and front passenger seat beltbuckles are equipped with sensors thatdetect if the seat belts are fastened. TheAdvanced Air Bag System moni
WARNING● Never let children ride unrestrained orextend their hands or face out of thewindow. Do not attempt to hold them inyour lap or arms. Some exam
WARNING● Children may be severely injured orkilled when the front air bags, side airbags or curtain air bags inflate if theyare not properly restraine
WARNINGFront seat-mounted side-impact supple-mental air bags and roof-mounted curtainside-impact supplemental air bags:● The side air bags and curtain
SSS0159 SSS0162Safety—Seats, seat belts and supplemental restraint system 1-49Z REVIEW COPY—2009 Altima (alt)Owners Manual (owners)—USA_English (nna)0
CoupeWRS08451-50 Safety—Seats, seat belts and supplemental restraint systemZ REVIEW COPY—2009 Altima (alt)Owners Manual (owners)—USA_English (nna)02/0
1. Roof-mounted curtain side-impactsupplemental air bag inflators2. Roof-mounted curtain side-impactsupplemental air bags3. Front seat-mounted side-im
0 Illustrated table of contentsAir bags, seat belts and child restraints ...0-2Exterior front ...0-3Exte
NISSAN Advanced Air Bag System(front seats)This vehicle is equipped with the NISSAN Ad-vanced Air Bag System for the driver and frontpassenger seats.
Front passenger air bag and status lightWARNINGThe front passenger air bag is designed toautomatically turn OFF under some con-ditions. Read this sect
NISSAN recommends that pre-teens and chil-dren be properly restrained in a rear seat.NISSAN also recommends that appropriate childrestraints and boost
● Do not place objects with sharp edgeson the seat. Also, do not place heavyobjects on the seat that will leave per-manent impressions in the seat. Su
Front seat-mounted side-impactsupplemental air bag and roof-mounted curtain side-impactsupplemental air bag systemsThe side air bags are located in th
● Right after inflation, several side air bagand curtain air bag system componentswill be hot. Do not touch them; you mayseverely burn yourself.● No u
When a pretensioner activates, smoke is re-leased and a loud noise may be heard. Thissmoke is not harmful and does not indicate a fire.Care should be
When the ignition is placed in the ON position,the supplemental air bag warning light illuminatesfor about 7 seconds and then turns off. Thismeans the
2 Instruments and controlsInstrument panel...2-2Meters and gauges ...2-3Speedometer and O
Covered storage box...2-42Grocery hooks (if so equipped) ...2-43Cargo net (if so equipped)...
1. Top tether strap anchor (P. 1-27)2. Rear seat belts (P. 1-15)3. Roof-mounted curtain side-impactsupplemental air bag (P. 1-43)4. Front seat-mounted
1. Vents (P. 4-10)2. Headlight/fog light (if so equipped)/turnsignal switch (P. 2-29)3. Steering wheel switch for audio control(if so equipped)/Blueto
20. Traction Control System (TCS) OFFswitch (if so equipped) (P. 5-25)Trunk opener (P. 3-23)Vehicle Dynamic Control (VDC) OFFswitch (if so equipped) (
1. Speedometer2. Change button3. Odometer/twin trip odometerSPEEDOMETER AND ODOMETERSpeedometerThe speedometers1indicates vehicle speed inmiles per ho
TACHOMETERThe tachometer indicates engine speed in revo-lutions per minute (rpm). Do not rev engine intothe red zones1.CAUTIONWhen engine speed approa
FUEL GAUGEThe gauge indicates the approximate fuel levelin the tank.The gauge may move slightly during braking,turning, acceleration, or going up or d
Push the button for about 1 second whenthe ignition switch is placed in the ON position totoggle the compass displays1on or off. Thedisplay will indic
● If a magnet is located near the com-pass or the vehicle is driven where theterrestrial magnetism is disturbed, thecompass display may not indicate t
● The compass may not indicate the correctcompass point in tunnels or while driving upor down a steep hill. (The compass returnsto the correct compass
or Anti-lock Braking System (ABS)warning lightNISSAN Intelligent Key™ warning light Security indicator lightor Brake warning lightSeat belt warning li
WARNING LIGHTSor Anti-lock BrakingSystem (ABS)warning lightWhen the ignition switch is placed in the ONposition, the Anti-lock Braking System (ABS)war
Coupe1. Power windows (P. 2-44)2. Windshield (P. 8-20)3. Windshield wiper and washer switch(P. 2-27)4. Engine hood (P. 3-23)5. Tie down/towing hooks (
Engine oil pressure warninglightThis light warns of low engine oil pressure. If thelight flickers or comes on during normal driving,pull off the road
● If the light illuminates while driving,avoid sudden steering maneuvers orabrupt braking, reduce vehicle speed,pull off the road to a safe location a
The seat belt warning light may also illuminate ifthe front passenger’s seat belt is not fastenedwhen the front passenger’s seat is occupied. For7 sec
The Malfunction Indicator Light may also comeon steady if the fuel-filler cap is loose or missing,or if the vehicle runs out of fuel. Check to makesur
The slip indicator light also comes on when youplace the ignition switch in the ON position. Thelight will turn off after about 2 seconds if thesystem
Light reminder chimeWith the ignition switch placed in the OFF posi-tion, a chime sounds when the driver’s door isopened if the headlights or parking
Fuel Economy modeThe fuel economy mode can be selected to dis-play the instant fuel economy since the last reset.Average speed modeThe average speed m
Range modeThe range mode can be selected to give you anestimation of the distance that can be drivenbefore refueling. The range is constantly calcu-la
Alert modeThe alert mode allows you to set alerts notifyingyou of time to rest or icy conditions.The time to rest alert lets you know when youhave bee
Display modeThe LANGUAGE/UNIT screen will appear whenselecting the “Language/Unit” key andpressing.Language: English or FrenchUnit: US — mile, °F, MPG
Comments to this Manuals